3340B71 INTERMEDIATE RIGID PIPING FITTING, LH REAR BRAKE - R R - Fiat - CROMA - eLearn

194000510 - 3340B71 INTERMEDIATE RIGID PIPING FITTING, LH REAR BRAKE - R R

) - Position the vehicle on a lift.- Make sure that the ignition key is in the OFF position, then disconnect the battery terminal (-).

	Description	Connector
-	Battery	See A001 BATTERY

Op. 4450B08 RIGHT REAR WHEEL - R.R Op. 7055B45 RIGHT REAR WHEEL ARCH LINER - R.R Op. 1040A30 FUEL FILLER PIPE ASSEMBLY- R + R Op. 1076B20 REAR EXHAUST SILENCER - R + R Op. 1076B30 FRONT EXHAUST SILENCER - R + R Op. 1040A10 FUEL TANK - R + R AND DECANT FUEL- Remove the protective cap from the bleed valve on the brake caliper.- Connect the recovery device (pipe and reservoir) to the brake caliper bleed valve.- Loosen the bleed valve on the brake caliper and wiat until the brake-clutch reservoir and the pipes drain.1. Undo the rear connector (1a) and disconnect the rigid intermediate pipe from the connector to the left rear brake connector (1b).

1. Working underneath the vehicle, undo the bolts (1a) and remove the front pipe protection (1b).

1. Undo the rear pipe protection and remove it.2. Undo the bolts (2a) and remove the bracket (2b).

1. Undo the bolts (1a) and (1b), then remove the right underbody reinforcement (1c).

1. Undo the front connector (1a) and disconnect the rigid intermediate pipe from the connector to the left rear brake connector (1b).

1. Release the rigid intermediate pipe from the left rear brake connector (1a) from the underbody fastenings (1b) and remove it.

Refitting ( Removing

) - Place the rigid intermediate pipe from the connector to the left rear brake connector back in its housing and secure it using the underbody clips.1. Connect the rigid intermediate pipe from the connector to the left rear brake connector (1a) and tighten the front connector (1b) to the recommended torque.

Component	Fastening	dia	Value (daNm)	Validity
Brake pipe connectors	Connector	M10/M12	1.4 ÷ 1.8

1. Place the underbody reinforcement (1a) in its housing and secure it tightening the new bolts (1b) and (1c) to the recommended torque.

Component	Fastening	dia	Value (daNm)	Validity
Underbody reinforcements	Inner bolt (to replace)	M12	(bodyshell side) 8.1 - 9.9 + 45°

Component	Fastening	dia	Value (daNm)	Validity
Underbody reinforcements	Outer bolt (to replace)	M10	(bodyshell side) 5.0 - 6.1 + 45°

Component	Fastening	dia	Value (daNm)	Validity
Underbody reinforcements	Bolt (to be replaced)	M12	(front suspension frame side) 9.0 - 11.0 + 90°

- Fit the bracket in its housing and secure it using the bolts.- Place the rear pipe guard in its housing and secure it using the bolts.- Place the front pipe guard in its housing and secure it using the bolts.1. Connect the rigid intermediate pipe from the connector to the left rear brake connector (1a) and tighten the rear connector (1b) to the recommended torque.

Component	Fastening	dia	Value (daNm)	Validity
Brake pipe connectors	Connector	M10/M12	1.4 ÷ 1.8

Op. 1040A10 FUEL TANK - R + R AND DECANT FUEL Op. 1076B30 FRONT EXHAUST SILENCER - R + R Op. 1076B20 REAR EXHAUST SILENCER - R + R Op. 1040A30 FUEL FILLER PIPE ASSEMBLY- R + R Op. 0010T64 BRAKE AND/OR CLUTCH FLUID CHECK LEVEL AND TOP UP AS NECESSARY Op. 0010T65 HYDRAULIC BRAKE SYSTEM - BLEED AIR Op. 7055B45 RIGHT REAR WHEEL ARCH LINER - R.R Op. 4450B08 RIGHT REAR WHEEL - R.R- Connect the negative battery terminal.- Remove the vehicle from the lift.