194001252 - 7210E66 R.R. REAR BUMPER

Removing ( Refitting ) - Turn the ignition key to the OFF position.- Open the bonnet.- Disconnect the negative battery terminal.

	Description	Connector
	BATTERY	See A001 BATTERY

FOLLOW ALL THE RECOMMENDED SAFETY INSTRUCTIONS    Op. 5580C AIR BAG SYSTEM

Follow the instructions for handling speakers.    Op. 5570 ACCESSORIES

1. Open the passenger compartment tailgate and unscrew the five upper bolts. 1. Unscrew the two bolts under the beam. - Working on both sides:    Op. 4450B13 REAR WHEELS (TWO) - R.R1. Unscrew the bolts (1a) securing the wheel arch to the inner edge of the wing on the bumper.2. Using the special tool, release the three retaining buttons (2a) and the wheel arch retainer (2b).

Tool	Description	Function	Validity
1878077000	Knife	Retainer removal

- Partly move aside the wheel arch to gain access to the bolt.1. Undo the retaining bolt. 1. Unscrew both bolts (1a) securing the outer tail-light (1b) and prise out of its seat without disconnecting the connectors. 1. Undo the two bolts (1a) fixing the bumpers (1b) to the vehicle.     Op. 7040B22 LUGGAGE COMPARTMENT/LOAD PLATFORM MOULDING - R+R    Op. 7040B26 LOAD PLATFORM COVER BLIND - R+R    Op. 7040B42 PROTECTION GRILLE FOR ANIMAL TRANSPORT - R and R    Op. 7040G46 LOAD COMPARTMENT COURTESY LIGHT - R and R    Op. 7050A47 SIDE PANEL ONE OF REAR SEAT SQUAB LH OR RH R R    Op. 7040B24 LOAD COMPARTMENT TOP TRIM (ONE) - R+R    Op. 7040B10 LOAD PLATFORM (LUGGAGE PLATFORM) TRIM - R+R    Op. 7040B18 LOAD COMPARTMENT LOAD PLATFORM SIDE TRIM ONE LH OR RH - R.R    Op. 5570T95 SUBWOOFER WITH AMPLIFIER BUILT INTO SOUND SYSTEM - R.R.1. Undo the bolt fixing the bumper at the side. 1. Unscrew the bolt with the extension in the box section. 1. Move aside the bumper to gain access to the number plate light and parking sensor connector.2. Disconnect the parking sensor connector (2a) and withdraw the bulb holder from the number plate lights (2b).

	Description	Connector
2a	PARKING SENSOR COUPLING	See D089 PARKING SENSOR COUPLING

	Description	Connector
2b	LEFT NO. PLATE LIGHT	See F050 LEFT NUMBER PLATE LIGHT

	Description	Connector
2b	RIGHT NO. PLATE LIGHT	See F051 RIGHT NUMBER PLATE LIGHT

1. Disconnect the bumper from the vehicle. Refitting ( Removing ) - Check that the bumper is not damaged.- Position the bumper in the housing.- Insert the bulb holder in the number plate lights.

	Description	Connector
	LEFT NO. PLATE LIGHT	See F050 LEFT NUMBER PLATE LIGHT

	Description	Connector
	RIGHT NO. PLATE LIGHT	See F051 RIGHT NUMBER PLATE LIGHT

- Connect the electrical connection for the parking sensors.

	Description	Connector
	PARKING SENSOR COUPLING	See D089 PARKING SENSOR COUPLING

Working on both sides:- Tignten the bolt with extension in the box section.- Tignten the side bumper bolt in the box section.    Op. 5570T95 SUBWOOFER WITH AMPLIFIER BUILT INTO SOUND SYSTEM - R.R.    Op. 7040B18 LOAD COMPARTMENT LOAD PLATFORM SIDE TRIM ONE LH OR RH - R.R    Op. 7040B10 LOAD PLATFORM (LUGGAGE PLATFORM) TRIM - R+R    Op. 7040B24 LOAD COMPARTMENT TOP TRIM (ONE) - R+R    Op. 7050A47 SIDE PANEL ONE OF REAR SEAT SQUAB LH OR RH R R    Op. 7040G46 LOAD COMPARTMENT COURTESY LIGHT - R and R    Op. 7040B42 PROTECTION GRILLE FOR ANIMAL TRANSPORT - R and R    Op. 7040B26 LOAD PLATFORM COVER BLIND - R+R    Op. 7040B22 LUGGAGE COMPARTMENT/LOAD PLATFORM MOULDING - R+R- Tighten both bolts in the outer tail-light seat.- Position the outer tail-light in its seat and tighten the bolts.- Tighten the bumper side bolt under the wheel arch.- Use an appropriate tool to fit the wheel arch in the retaining bell housing.

Tool	Description	Function	Validity
1878077000	Knife	Retainer removal

- Attach the wheel arch retaining studs.    Op. 4450B13 REAR WHEELS (TWO) - R.R- Tighten the two bolts under the beam.- Tighten the five upper retaining bolts.- Connect the negative battery terminal once again.

	Description	Connector
	BATTERY	See A001 BATTERY