194000195 - 5580P CONNECT PANEL
CONNECT NAV +
Dimensions: 2DIN box with front panel integrated in the vehicle dashboard.The system includes:- radio- CD ROM reader- GPS module- dual band telephone GSM module- navigation system with maps- assistance services- 6.5" TFT colour display- Blaupunkt external CD changer system (if present).- MP3- built-in voice recognition module- WAP protocol- steering wheel controlsInternal modules description
CD ROM readerThe Connect is equpped with a CD ROM reader capable of reading and managing both CDs (audio/MP3) and management CDs (system or navigation maps).CD changerThe Connect is also designed to operate external CD Changer and to accept analogue audio output. The device is a Blaupunkt CD changer with 5 discs located in the oddments compartment on the passenger side.GSM ModuleThe Connect is equipped with a dual band telephone module and a SIM card reader (where the user can insert the SIM card).There is an external microphone (hands-free and voice recognition usage).Radio - CD moduleGeneral specifications:- music audio power: 4x35W- 5 band graphic equalizer- easy to manage menu for the adjustment of the radio settings and any external interfaces (CD-Changer)- remote control from the steering wheel- possibility of interface with outside CD Changer.- speed dependent volume control- possibility of activating certain commands via voice recognition module.Radio specifications:- RDS- RDS - TMC (Traffic Message Channel)- EON (Enhanced Other Network)- TA (Traffic Announcements)- tuning to the following bands: USW (87.5-108 Mhz) (FM); MW (153-279 khz) (AM); LW (531-1602 khz) (AM);It is also possible to store:-24 FM stations (6 of which can be memorized through autostore);-6 MW stations;-6 LW stations;- 6 stations that can be memorized through autostore on the AMST band;- 2 scan modes (short lislten to a station and automatic transfer to the next):- scanning the frequency band used;- scanning programmed stations;- possibility of selecting programmes via PTY (on FM bands only);- setting sensitivity: local / distance.Audio management:- bass- balance- fader- loudness- treble- Hi-Fi system active control- muteThere are 5 equalizing curves:- best (manufacturer''s equalizing data);- rock;- jazz;- classical;- manual (can be set via 5 band graphic equalizer).CD specifications:- motorized loading and ejection- TPM function (Track Program Memory)- shuffle function- repeat- skip- pause / stop- compression: the CD noise dynamic reduction circuit- CD naming: CD identification (20 characters max)MP3 CD specifications:- play list function (such as TPM for audio CD)- functions associated with the play list:- scan;- repeat (one track or all);- pause;- skip;- maximum number of MP3 tracks considered for each CD: 999 (if the number of MP3 files contained in the CD is higher than this limit, only the first 999 will be considered).- compression: activates the CD noise dynamic reduction circuit.Blaupunkt 5 disc CD changer specifications (in the passenger side oddments compartment):- scan function- repeat function- shuffle function- CD naming- compression: activates the CD noise dynamic reduction circuit.Management of controls from steering wheel- the audio module can be managed by the buttons on the steering wheel.System activation
The CONNECT system may be activated in two different modes:- Automatic activation with the key inserted and turned to the ON position- Manual activation by means of ON button-- Emergency manual activation by means of SOS buttonAutomatic activationWhen the ignition key is turned to ON position, the CONNECT system turns on automatically to make all the functions described in this chapter active or enabled.Manual activationWith the ignition key in OFF position, the CONNECT system comes on when the ON button is pressed to make the following modes available:- MAIN- AUDIO- NAV- TEL- SOS and SERVICE (Targasys)In this mode, the SETUP and TRIP modules can be activated but it is not possible to validate any parameter change, language change or measurement unit change or any other type of adjustment envisaged by the CONNECT system. These limitations are normal when the system is activated by means of the ON button. When the vehicle is not running (key extracted or OFF position), the data transmission devices inside the vehicle are not operational. When ignition key is turned ON, the system begins to work.System deactivation
The CONNECT system may be activated in two different modes:- deactivation independent of the ignition key;- deactivation dependent on the ignition key.To choose the deactivation mode, see the Power OFF submenu in the SEPUP menu.Deactivation independent of the ignition keyWhen this mode is active, the CONNECT system may be turned off by pressing the ON button.The display shows the message DEACTIVATION PROCEDURE IN PROGRESS, WAIT A FEW MOMENTS.With the ignition key extracted or in the OFF position, the system deactivates with a delay of 20 minutes if a system destination has been set or if a phone conversation is in progress.Deactivation dependent on the ignition keyWhen this mode is active, the CONNECT system may be turned off by turning the ignition key to the OFF position.Front of the connect nav+
FRONT VIEW
| Keys | Short press on key (less than 2 second) | Prolonged press on key (longer than 2 seconds) |
|---|---|---|
| 1 | Activation or interruption of the Voice Recognition function | Activation or interruption of the Voice Recognition function. Activation of the Voice Memo function, this can be interrupted by a further short or long press on the button |
| 2 | Choice of audio source:FM1/2/3/AST –MW/LW/AMAST – CD – CDC | - |
| 3 | - Send the selected phone call- Reselect the last number dialled and then press the key with 5 seconds to send a call to the number- Accept incoming phone call | - Refuse incoming phone call- Stop dialling a new phone number- Interrupt a phone call already in progress |
| 4 | Activate TRIP on-board computer mode | - |
| 5 | Radio mode: search for the first radio station at a lower frequencyCD mode: select the previous track.MP3 mode: select the previous track. | Radio mode: activate scanning function for lower frequencies, station scanning will stop at the first station with an audible signal.CD mode: select the previous track.MP3 mode: move to the previous 10 tracks or the previous folder. |
| 6 | Radio mode: search for the first radio station at a higher frequencyCD mode: select the next track.MP3 mode: select the next track. | Radio mode: activate scanning function for higher frequencies, station scanning will stop at the first station with an audible signal.CD mode: select the next track.MP3 mode: move to the next 10 tracks or the next folder. |
| 7 | CD housing | - |
| 8 | Eject navigation CD-ROM or audio CD | - |
| 9 | Play/stop for CD/CDC | Pause for CD/CDC |
| 10 | SIM CARD housing eject key | - |
| 11 | SIM CARD housing | - |
| 12 | Activate SOS mode (assistance functions and services) | - |
| 13 | Targasys mode activation | - |
| 14 | Exit from a selection menu or leave a submenu of a higher menu | - |
| 15 | Knob for selecting the required function. Press to confirm | - |
| 16 | Multifunction key. Function depends on active mode.The function is always identified by graphic buttons that appear on the display. In some cases the area of the graphic button may cover several adjacent multifunction buttons: the function of the keys under this area is the same | - |
| 17 | Knob for adjusting volume level. Press to turn the system on/off | - |
| 18 | Activate navigation mode | Activate/deactivate the MUTE function for navigation information |
| 19 | Activate phone mode | Phone on/off |
| 20 | Activate Audio mode | Activate/deactivate the MUTE function for audio sources |
| 21 | Activate Main mode | Dark mode: The display is darkened completely.The display is lit again by pressing the MAIN, TEL, SOS buttons or by receiving a phone call |
Controls on the steering wheel
The controls for the main functions of the CONNECT are duplicated on the steering wheel for greater ease. The configuration used for the CONNECT NAV+ is 8+3 buttons
| Key | Short press on key (less than 2 second) | Prolonged press on key (longer than 2 seconds) |
|---|---|---|
| VOL +/- | Raises or lowers volume level | Raises or lowers volume level |
| VOICE | Activation or interruption of the Voice Recognition function | Activation of the Voice Memo function, this can be interrupted by a further short or long press on the button |
| SOURCE | Select operating mode: FM1/2/3AST-MW / LW / AMAST - CD - CDC | - |
| SCAN +/- | The “SCAN +/-” buttons allow:- In Radio mode: to search for the next or previous radio station- In CD/MP3/CDC mode: to move to the previous or next track | - |
| TEL | - Send the selected phone call- Reselect the last number dialled and then press the key with 5 seconds to send a call to the number- Accept incoming phone call | - Refuse incoming phone call- Stop dialling a new phone number- Interrupt a phone call already in progress |
| MENU | The MENU button is used to select the various CONNECT modes: MAIN, AUDIO, TRIP, TEL, NAV, MAIN etc starting from the current active mode | - |
Functional description
Power supply managementEvents that interact with the power supply managementThe events that directly or indirectly allow the user to interact with the general system operating state are:- + key: physical signal linked to the key status (panel/engine on).- on/off button: present on the Connect front panel.- SOS button: present on the Connect front panel.Possible system statesPossible Connect statuses from the viewpoint of power supply and operation in general are as follows: off state, normal state, stand-by state.Operation still depends on the "system configuration". The configuration of the system memorizes which functions the user has selected as active.The functions are: tuner, CD, CD Changer, telephone, service call and video (dark on/off).- off state: all Connect functions are disabled and the various hardware modules are not supplied with power.- normal state: in the normal state, the Connect system is fully active and all system functions are managed in accordance with the system configuration. Internal modules are operational, as are the internal communication lines.- stand-by state: in this status, the Connect system is active but looks exactly as though it were OFF to the user. In any case the only internal module that is fully operational is the network communcation.PLANNED ACTIONSSwitching on| ... DATA ERROR - CROPPED TEXT | Ошибка данных - Текст обрезан ... |
|---|