198001483 - 5050 SCREEN WASHERS AND HEADLAMP WASH/WIPE
SPECIFICATIONS
The vehicle is equipped with a system that cleans and washes the front windscreen. The vehicle may be fitted as an option with a pressurised liquid washing system for the front headlamps.Reservoir
The reservoir is located in the left side of the wheel arch compartment and it allows the screen washer system pump to supply the water-antifreeze mixture required to clean the front window. If the vehicle is equipped with the relevant option, it also supplies the headlamp washer system via a special pump.The reservoir capacity ensures a minimum of 25 washing cycles and it ranges in size from a minimum of about 5 litres for the version without a headlamp washer to up to around 6 litres if equipped with a headlamp washer.The reservoir is made out of plastic and contains external housings for the pump that supplies the windscreen washer and headlamp washers (if fitted).1 - Windscreen washer fluid reservoir2 - Pump supplying fluid to the nozzles
Controls
The control of the wiping functions and, in particular, of the:- windscreen wiper: sweep rate;- rearscreen wiper: sweep rate and control during reversing;- windscreen wiper function: smart washing;- rearscreen washer function: smart washing;is managed by the electronic module inside the steering column switch unit.The right lever allows the activation of the various functions.Operation
Windscreen wiper
Manual mode operation- Pos. A: OFF- Pos. B: Intermittent / Automatic- Pos. C: Continuous 1st speed- Pos. D: Continuous 2nd speed- Pos. E: Anti-panic (temporary speed - unstable)When the ring nut for the steering column switch unit right lever is moved downwards, to one of the three positions:- intermittent- first speed continuous- second speed continuousthe windscreen wiper motor is activated according to the following logic.Intermittent: the windscreen wiper is operated at the first speed but with a pause between one stroke and the next, that varies according to the speed of the vehicle (from a minimum of 1.1 secs. above 110 km/h to a maximum of 4.7 secs with the vehicle stationary).First speed continuous: the windscreen wiper is operated at the first speed at 45 strokes/minute.Second speed continuous: the windscreen wiper is operated at the second speed at 65 strokes/minute.Automatic mode operationA special rain sensor manages the automatic operation: it is a sensor with an infrared LED installed in the windscreen capable of detecting the presence of rain and, consequently, of managing the wiping depending on the water present on the glass.
The rain sensor is activated by placing the ring nut for the right steering column switch unit lever in the intermittent-automatic position. The frequency of the windscreen wiper strokes is automatically adjusted depending on the amount of water on the windscreen. This frequency can vary from no stroke (no rain - windscreen dry) up to the second continuous speed (heavy rain - windscreen wet).The activation of the rain sensor involves a windscreen wiper arm stroke as feedback to confirm that it has been switched on.
The user can alter the sensitivity of the rain sensor, using the vehicle set up menu in the instrument panel. |
If the vehicle is switched off leaving the ring nut in the intermittent-automatic position, the next time it is switched back on there is no wiping cycle even if there is rain; this prevents accidental activation which could cause dangerous conditions for the user (for example, washing the windscreen by hand, blades stuck frozen , etc.). |
1 - Sensitive element2 - Retaining structure3 - Cover4 - Contact disc
The layer of silicone material is protected by a film that is removed when the component is installed. Avoid touching with your hands to prevent damage to the silicone. Because it is not possile to disconnect and reconnect the part without damaging the silicone layer, the sensor should be replaced if the windscreen is replaced. |
If a new part is installed during service, check that no air bubbles remain between the glass and sensor, apply a load of at least 50N to ensure any bubbles emerge. |
Rearscreen wiper
When the rearscreen wiper ring nut located on the right steering column switch unit lever is turned, the rearscreen wiper is activated in one of the following modes:- intermittent: with a pause of 2.7 secs. between one stroke and the next- subject to the windscreen wiper (if there is a simultaneous windscreen/rearscreen wiper request): In this case the operation is synchronous with a frequency equal to half that of the windscreen wiper- if reverse gear is engaged it is continuous.
Windscreen washer
Front windscreen washingPulling the right steering column switch unit lever activates the front washing.Keeping the lever pulled for more than 0.5 secs automatically activates the windscreen wiper at the first continuous speed.When the control is released there are a further 3 strokes to clean the windscreen plus another one 6 seconds later (to remove any drips).If the windscreen wiper was already activated before the washing command using the lever, the washing logic is only effective for activating intermittent operation.Rear windscreen washingPushing the right steering column switch unit lever activates the rear washing. Keeping the lever pushed for more than 0.5 secs automatically activates the rearscreen wiper at the continuous speed.When the control is released there are a further 3 strokes to clean the rearscreen plus another one 6 seconds later (to remove any drips).If the rearscreen wiper was already activated before the washing command using the lever, the washing logic is only effective for activating intermittent operation.