198002520 - 7210B40 R.R. REAR INNER WHEEL ARCH

Removing ( Refitting )     Op. 7210B82 R.R REAR CROSSMEMBER     Op. 7210E36 R.R. FRONT SIDE DOOR     Op. 7210E38 R.R. REAR SIDE DOOR     Op. 7210E56 R.R. TAILGATE     Op. 7210E52 R.R. REAR WING     Op. 7210B50 R.R. REAR WING LOWER FRAME    Op. 7210B75 R.R. REAR LIGHT CLUSTER HOUSING     Op. 7210E72 R.R. FUEL FILLER BUSH WITH WING REMOVED    Op. 7210E28 R.R. ROOF PANEL     Op. 7210E34 R.R. ROOF PANEL/SIDE PANEL CONNECTION PROFILE-MOULDING     Op. 7210B51 R R UPPER CHANNEL STIFFENER, (ONE) LH OR RH     Op. 7210B80 R.R. BODYSHELL REAR CROSSMEMBER    Op. 7210B65 R.R. REAR PILLAR (WING INTERIOR)     Op. 7210B45 R.R. REAR WING FRAME - Ensure that the components connected are not distorted by checking the bodyshell alignment measurements with suitable equipment (gauges, templates or jigs).- Straighten the body as necessary. - Use a rotary brush to remove the paint and gain access to the spot welds.1. Use the chamfering machine to remove the spot welds shown in the diagram.- Use the drill to chamfer the spot welds that are not accessible to the chamfering machine.- Use a hammer and chisel to remove the previously chamfered spot welds.- Remove the part from the vehicle. - Straighten the edges of the vehicle using a hammer and dolly block.- Remove the spot weld residues using a disc grinder.- Use a rotary brush to clean the previously treated areas.1. Apply electro-galvanizing paint. 1. Remove the anti-corrosion treatment from the entire perimeter of the inside and outside of the replacement part using a rotary brush.2. Drill out the part at the indicated points.- Apply electro-weldable paint to the edges involved. Refitting ( Removing ) 1. Position the replacement part correctly on the vehicle and secure it using self-locking clamps.- Check the alignment and the surrounding gaps.2. Use a spot welder to weld the areas shown in the diagram.3. Use a MIG welder to fill weld the openings made previously. - Correct any distortions to the panel using a mallet and dolly block.1. Use a disc grinder to level the welds.- Use a rotary brush to clean the previously welded areas. 1. Apply anti-oxidant protection to the areas involved in the welding.- Seal the join lines between the replacement part and the vehicle.     Op. 7210B45 R.R. REAR WING FRAME     Op. 7210B65 R.R. REAR PILLAR (WING INTERIOR)     Op. 7210B80 R.R. BODYSHELL REAR CROSSMEMBER    Op. 7210B51 R R UPPER CHANNEL STIFFENER, (ONE) LH OR RH     Op. 7210E34 R.R. ROOF PANEL/SIDE PANEL CONNECTION PROFILE-MOULDING     Op. 7210E28 R.R. ROOF PANEL     Op. 7210E72 R.R. FUEL FILLER BUSH WITH WING REMOVED    Op. 7210B75 R.R. REAR LIGHT CLUSTER HOUSING     Op. 7210B50 R.R. REAR WING LOWER FRAME    Op. 7210E52 R.R. REAR WING     Op. 7210E56 R.R. TAILGATE     Op. 7210E38 R.R. REAR SIDE DOOR     Op. 7210E36 R.R. FRONT SIDE DOOR     Op. 7210B82 R.R REAR CROSSMEMBER