198002151 - 4410D13 FRONT SUSPENSION CROSSMEMBER - R.R

Removing ( Refitting )     Op. 4450B12 FRONT WHEELS (TWO) - R+R     Op. 7055B65 ENGINE COMPARTMENT DUST COVER IN LEFT FRONT WHEEL ARCH - R.R.     Op. 7055B66 ENGINE COMPARTMENT DUST COVER IN RIGHT FRONT WHEEL ARCH - R.R.     Op. 1048A10 AIR FILTER ASSEMBLY - R.R.     Op. 1072C44 EXHAUST MANIFOLD HEAT SHIELD - R+R     Op. 4410D17 REINFORCEMENT FOR FRONT SUSPENSION CROSSMEMBER - R.R.    Op. 7055B54 UNDER ENGINE PROTECTION/GUARD - R.R.     Op. 1072C16 EXHAUST MANIFOLD WITH CATALYTIC CONVERTER - R.R.     Op. 1008C32 GEARBOX LOWER REACTION ROD -R.R.
The left-hand side of the suspension crossmember is shown below; proceed in the same way for the right-hand side.
1. Undo the bolts securing the anti-roll bar to the suspension crossmember.2. Undo the bolt securing the steering box to the suspension crossmember.3. Undo the bolts securing the wishbone to the suspension crossmember.
- Set up the tool for removing/refitting the suspension crossmember as described below.1. Fit mount (1a) onto column lift (1b).
ToolDescriptionFunctionValidity
2000001700MountSuspension crossmember support
ToolDescriptionFunctionValidity
1870835001Column liftSuspension crossmember support
2. Fit frame (2a) and secure it to the mounting with retaining pins (2b) and (2c).
ToolDescriptionFunctionValidity
2000024400ChassisSuspension crossmember support
ToolDescriptionFunctionValidity
2000024419PinFrame connection to suspension mounting
ToolDescriptionFunctionValidity
2000024418PinFrame connection to suspension mounting
3. Fit pins (3a), (3b), (3c) and (3d) onto frame (2a), as shown in the diagram.
ToolDescriptionFunctionValidity
2000024413PinFront suspension crossmember support
ToolDescriptionFunctionValidity
2000024412PinFront suspension crossmember support
ToolDescriptionFunctionValidity
2000024410PinFront suspension crossmember support
ToolDescriptionFunctionValidity
2000024411PinFront suspension crossmember support
- If the above hydraulic lift is not available, use a general hydraulic lift plus the adaptor shown in the drawing, which must be made up by the workshop to allow the use of the frames mentioned above.
(*): Adapt the shank diameter to fit the hydraulic lift used1. Support the suspension crossmember using the equipment prepared previously, taking care that the pins are positioned in the axle-body locating openings as illustrated.2. Insert the split pins onto the pins to secure the crossmember to the support frame during the entire phase of removal from the vehicle.3. Unscrew bolts (3a) securing suspension crossmember (3b) to the body, bolts (3c) securing the crossmember to the side panels and remove it from its housing.
1. Disconnect split pins (1a) and remove suspension crossmember (1b) from the support frame.
Refitting ( Removing ) - Position the suspension crossmember on the support frame and secure it with the associated split pins.- Place the suspension crossmember in position using the equipment used for the removal, taking care that the adaptors are positioned in the axle-body locating openings.- Tighten the bolts securing the suspension crossmember to the body and side panels to the specified torque.
ComponentFasteningdia  Value (daNm)Validity
Front suspension crossmember to bodyshellBolt (to be replaced)M129.9 ÷ 12.1
ComponentFasteningdia  Value (daNm)Validity
Front suspension crossmember to bodyshellBolt (to be replaced)M1413.5 ÷ 16.5
- Remove the equipment used for refitting the suspension crossmember.- Tighten the bolts securing the wishbone to the suspension crossmember to the recommended torque.
ComponentFasteningdia  Value (daNm)Validity
Lower track control arm to front suspension crossmemberBoltM1211.5 ÷ 12.5
ComponentFasteningdia  Value (daNm)Validity
Lower track control arm to front suspension crossmemberBoltM1417.5 ÷ 19.5
- Tighten the bolt securing the steering box to the suspension crossmember to the recommended torque.
ComponentFasteningdia  Value (daNm)Validity
Steering box to suspension crossmemberBoltM127.2 ÷ 8.8
- Tighten the bolts securing the anti-roll bar to the suspension crossmember to the recommended torque.
ComponentFasteningdia  Value (daNm)Validity
Anti-roll bar to front suspension crossmemberBoltM82.3 ÷ 2.7
    Op. 1008C32 GEARBOX LOWER REACTION ROD -R.R.     Op. 1072C16 EXHAUST MANIFOLD WITH CATALYTIC CONVERTER - R.R.     Op. 7055B54 UNDER ENGINE PROTECTION/GUARD - R.R.     Op. 4410D17 REINFORCEMENT FOR FRONT SUSPENSION CROSSMEMBER - R.R.    Op. 1072C44 EXHAUST MANIFOLD HEAT SHIELD - R+R     Op. 1048A10 AIR FILTER ASSEMBLY - R.R.     Op. 7055B66 ENGINE COMPARTMENT DUST COVER IN RIGHT FRONT WHEEL ARCH - R.R.     Op. 7055B65 ENGINE COMPARTMENT DUST COVER IN LEFT FRONT WHEEL ARCH - R.R.     Op. 4450B12 FRONT WHEELS (TWO) - R+R     Op. 4450A10 FRONT WHEEL GEOMETRY - CHECK USING OPTICAL EQUIPMENT - INCLUDES ADJUSTMENT IF NECESSARY