199001811 - C010 FIRST AND/OR REVERSE DOES NOT ENGAGE AFTER A STOP (Robotized gearbox)

		Test results
1	ERRORS IN AUTOMATED GEARBOX CONTROL UNIT CHECK	All OK	Problems encountered	Operation
	Check that there are no errors in the automated gearbox control unit. More specifically:- Clutch sensor error- Lever switch error (any of the 4 or ECO/Normal switch)- Microprocessor 2 error- Even gears engagement error- Odd gears engagement error- Clutch solenoid current error- Electro-magnetic brake error (Selection solenoid)- Control unit earths error- Load relay error	Move on to Step 5	One or more errors on the list are present	Move on to Step 2
2	CHECKS ON FAULTS ENCOUNTERED	All OK	Problems encountered	Operation
	Check the faults, carrying out    See Test 2127OI WHAT TO DO DEPENDING ON THE ERROR PRESENT IN THE ROBOTIZED GEARBOX CONTROL UNIT	Move on to Step 3	Fault at the connections (Clutch sensor, Even or uneven gears engagement error, Clutch solenoid current error, Gear selection electro-magnet (electro-magnetic brake) error, Control unit earths error and/or load relay error)	Restore/replace the wiring    See E7051 ROBOTIZED GEARBOX
			The displayed state is not correct (Lever switch error - Check lever)	Check connections, wiring continuity and gear lever    See E7051 ROBOTIZED GEARBOX
			The change of state does not take place and/or the word ECO is not displayed - Check ECO button	Check the button and the wiring    See E7051 ROBOTIZED GEARBOX
			The Automated Gearbox has been replaced (Microprocessor 2 error)	Move on to Step 4
			The active diagnosis is inconclusive and no wiring errors are detected (Even gears or odd gears engagement and/or Clutch solenoid current error)	Move on to Step 3
3	AFTER THE ACTIVE DIAGNOSIS ON THE SOLENOIDS	All OK	Problems encountered	Operation
	- If this step has been reached during the active diagnosis of the clutch solenoid, replace it    Op. 2127C56 CLUTCH CONTROL SOLENOID - R.R. and check it is working correctly by carrying out a gear change- If this step has been reached during the active diagnosis of the engagement solenoid, replace it    Op. 2127C52 ODD AND EVEN GEAR ENGAGEMENT SOLENOIDS - R.R. and check it is working correctly	Move on to Step 4
4	REPLACEMENT OF GEAR SELECTION SOLENOID	All OK	Problems encountered	Operation
	If no connection / wiring faults are detected and the gear selection solenoid is in error, replace it    Op. 2127C54 GEAR SELECTION SOLENOIDS - R.R. and check it is working correctly	Move on to Step 5
5	GEAR LEVER CHECK	All OK	Problems encountered	Operation
	Check that the gear lever is working properly, carrying out    See Test 2127OL GEAR LEVER CHECK	Move on to Step 6	The displayed lever states are not correct	Check the wiring and the gear switches/levers. Restore/replace the part that is not working
			The state does not change and/or the word AUTO is not displayed	Check the switch and the wiring. Restore/replace the part that is not working
6	FLUID LEVEL CHECK	All OK	Problems encountered	Operation
	Check the fluid level, carrying out    See Test 2127OB FLUID LEVEL CHECK	Move on to Step 8	Level lower than Max mark	Top up and move on to Step 7
			Level above Max mark	Bring to Max level and move on to step 8
7	FLUID LEAKS CHECK	All OK	Problems encountered	Operation
	Check there are no fluid leaks, carrying out    See Test 2127OC FLUID LEAKS CHECK	Move on to Step 8	Fluid leaks detected in the clutch assembly	Carry out the procedure for bleeding the clutch with Examiner in active diagnosis.
			Fluid leaks detected in other parts of the hydraulic assembly	Repair/replace the parts involved, top up the fluid.
8	FLUID PRESSURE CHECK	All OK	Problems encountered	Operation
	Check the fluid pressure, carrying out    See Test 2127OD FLUID PRESSURE CHECK	Move on to Step 11	Pressure < 40 bar	Move on to Step 9
9	PRESSURE SENSOR CHECK	All OK	Problems encountered	Operation
	Check that the sensor is working properly, carrying out    See T OIL PRESSURE SENSOR OPERATION CHECK	Move on to Step 10	Pressure sensor not working	Replace the sensor    Op. 2127E50 HYDRAULIC SELECTION GEARBOX CIRCUIT PRESSURE SENSOR - R.R.
10	ELECTRIC PUMP OPERATION CHECK	All OK	Problems encountered	Operation
	Check that the electric pump is working properly by carrying out    See Test 2127OE ELECTRIC PUMP OPERATION CHECK	Move on to Step 11	Voltage less than 11 V	Restore correct battery voltage.
			It is not possible to shift gears using the lever	Activate the "bleed clutch" function from Examiner Plus or Smart to activate the electric pump.
11	BRAKE PEDAL SWITCH CHECK	All OK	Problems encountered	Operation
	Check that the brake pedal switch is working properly, carrying out    See Test 2127OF BRAKE PEDAL SWITCH CHECK	Move on to Step 12	The brake pedal switch is not working properly	Check the switch on the brake pedal, its fastening, its positioning, the wiring and the engine management control unit. Restore/replace the part that is not working
12	CHECK THAT THE CLUTCH IS NOT DRIVEN	All OK	Problems encountered	Operation
	Check that the clutch is not driven, carrying out    See Test 2127OK CLUTCH DRIVE CHECK	Move on to Step 13	The clutch is driven	Replace the clutch mechanism    Op. 1810A28 CLUTCH - R R FOR MANUAL GEARBOX WITH HYDRAULIC SELECTION VERSIONS
13	CORRECT OPERATION CHECK	All OK	Problems encountered	Operation
	Check that the fault is no longer present.	End of diagnosis	The fault persists	Contact technical service for further information on the problem