199001813 - C012 REVERSE GEAR CAN SOMETIMES NOT BE ENGAGED (Robotized gearbox)

		Test results
1	ERRORS IN AUTOMATED GEARBOX CONTROL UNIT CHECK	All OK	Problems encountered	Operation
	Check that there are no errors in the automated gearbox control unit. More specifically:- Lever switch error (any of the 4 or ECO/Normal switch)- Gear selection Solenoid brake error	Move on to Step 4	One or more errors on the list are present	Move on to Step 2
2	CHECKS ON FAULTS ENCOUNTERED	All OK	Problems encountered	Operation
	Check the faults, carrying out    See Test 2127OI WHAT TO DO DEPENDING ON THE ERROR PRESENT IN THE ROBOTIZED GEARBOX CONTROL UNIT	Move on to Step 3	Fault at the connections (Gear selection solenoid error)	Restore/replace the wiring    See E7051 ROBOTIZED GEARBOX
			The displayed state is not correct (Lever switch error - Check lever)	Check connections, wiring continuity and gear lever.
			The change of state does not take place and/or the word ECO is not displayed (Lever switch error - Check ECO button)	Check the button and the wiring
3	REPLACEMENT OF GEAR SELECTION SOLENOID	All OK	Problems encountered	Operation
	If no connection / wiring faults are detected and the gear selection solenoid is in error, replace it    Op. 2127C54 GEAR SELECTION SOLENOIDS - R.R. and check it is working correctly	Move on to Step 4
4	GEAR LEVER CHECK	All OK	Problems encountered	Operation
	1. Check that the gear lever is working properly, carrying out    See Test 2127OL GEAR LEVER CHECK	Move on to Step 5	The displayed lever states are not correct	Check the wiring and the gear switches/levers. Restore/replace the part that is not working
			The state does not change and/or the word AUTO is not displayed	Check the switch and the wiring. Restore/replace the part that is not working
5	FLUID LEVEL CHECK	All OK	Problems encountered	Operation
	Check the fluid level, carrying out    See Test 2127OB FLUID LEVEL CHECK	Move on to Step 7	Level lower than Max mark	Top up and move on to Step 6
			Level above Max mark	Bring to Max level and move on to step 7
6	FLUID LEAKS CHECK	All OK	Problems encountered	Operation
	Check there are no fluid leaks, carrying out    See Test 2127OC FLUID LEAKS CHECK	Move on to Step 7	Fluid leaks detected in the clutch assembly	Carry out the procedure for bleeding the clutch with Examiner in active diagnosis
			Fluid leaks detected in other parts of the hydraulic assembly	Repair/replace the parts involved, top up the oil and check the seal
7	FLUID PRESSURE CHECK	All OK	Problems encountered	Operation
	Check the fluid pressure, carrying out    See Test 2127OD FLUID PRESSURE CHECK	Move on to Step 10	Pressure < 40 bar	Move on to Step 8
8	PRESSURE SENSOR CHECK	All OK	Problems encountered	Operation
	Check that the sensor is working properly, carrying out    See T OIL PRESSURE SENSOR OPERATION CHECK	Move on to Step 9	Pressure sensor not working	Replace the sensor    Op. 2127E50 HYDRAULIC SELECTION GEARBOX CIRCUIT PRESSURE SENSOR - R.R.
9	ELECTRIC PUMP OPERATION CHECK	All OK	Problems encountered	Operation
	Check that the electric pump is working properly by carrying out    See Test 2127OE ELECTRIC PUMP OPERATION CHECK	Move on to Step 10	Voltage less than 11 V	Restore correct battery voltage.
			It is not possible to shift gears using the lever	Activate the "bleed clutch" function from Examiner Plus or Smart to activate the electric pump.
10	CHECK THAT THE CLUTCH IS NOT DRIVEN	All OK	Problems encountered	Operation
	Check that the clutch is not driven, carrying out    See Test 2127OK CLUTCH DRIVE CHECK	Move on to Step 11	The clutch is driven	Replace the clutch mechanism    Op. 1810A28 CLUTCH - R R FOR MANUAL GEARBOX WITH HYDRAULIC SELECTION VERSIONS
11	CORRECT OPERATION CHECK	All OK	Problems encountered	Operation
	Check that the fault is no longer present	End of diagnosis	The fault persists	Contact technical service for further information on the problem