199001812 - C011 THE GEARS DO NOT ENGAGE WITH THE ENGINE HOT (Robotized gearbox)

1	ERRORS IN AUTOMATED GEARBOX CONTROL UNIT CHECK	All OK	Problems encountered	Operation
	Check that there are no errors in the automated gearbox control unit. More specifically:- Clutch sensor error- Lever switch error- Even gears engagement error- Odd gears engagement error- Clutch solenoid current error- Electro-magnetic brake error (Selection solenoid)	Move on to Step 2	Errors present.	Continue as instructed by the diagnostic equipment
2	CONTROL UNIT EARTH CONNECTION CHECKS	All OK	Problems encountered	Operation
	Check the connection to earth for the gearbox control unit, following the    See T CHECKING THE ROBOTIZED GEARBOX CONTROL UNIT POWER SUPPLY	End of diagnosis	Faulty control unit earth.	Restore the correct earth connections.
3	GEAR LEVER CHECK	All OK	Problems encountered	Operation
	Check that the gear lever is working properly, carrying out the    See Test 2127OL GEAR LEVER CHECK	Move on to Step 4	The displayed lever states are not correct	Check the wiring and the gear switches/levers. Restore/replace the part that is not working
			The state does not change and/or the word AUTO is not displayed	Check the switch and the wiring. Restore/replace the part that is not working
4	FLUID LEVEL CHECK	All OK	Problems encountered	Operation
	Check the fluid level, carrying out the    See Test 2127OB FLUID LEVEL CHECK	Move on to Step 6	Level lower than Max mark	Top up and move on to Step 5
			Level above Max mark	Bring to Max level and move on to step 6
5	FLUID LEAKS CHECK	All OK	Problems encountered	Operation
	Check there are no fluid leaks, carrying out the    See Test 2127OC FLUID LEAKS CHECK	Move on to Step 6	Fluid leaks detected in the clutch assembly	Carry out the procedure for bleeding the clutch with Examiner in active diagnosis.
			Fluid leaks detected in other parts of the hydraulic assembly.	Repair/replace the parts involved, top up the fluid.
6	FLUID PRESSURE CHECK	All OK	Problems encountered	Operation
	Check the oil pressure, carrying out the    See Test 2127OD FLUID PRESSURE CHECK	Move on to Step 9	Pressure < 40 bar	Move on to Step 7
7	PRESSURE SENSOR CHECK	All OK	Problems encountered	Operation
	Use Examiner to check that the pressure sensor is working properly.	Move on to Step 8	Pressure sensor not working.	Replace the sensor    Op. 2127E50 HYDRAULIC SELECTION GEARBOX CIRCUIT PRESSURE SENSOR - R.R.
8	ELECTRIC PUMP OPERATION CHECK	All OK	Problems encountered	Operation
	Check that the electric pump is working properly as shown in the    See Test 2127OE ELECTRIC PUMP OPERATION CHECK	Move on to Step 9	Voltage less than 11 V	Restore correct battery voltage.
			It is not possible to shift gears using the lever.	Activate the "bleed clutch" function from Examiner Plus or Smart to activate the electric pump.
9	CHECK THAT THE CLUTCH IS NOT DRIVEN	All OK	Problems encountered	Operation
	Check that the clutch is not driven, carrying out    See Test 2127OA CHECK ON OPERATION OF CLUTCH DISC SPEED SENSOR THROUGH ROAD TEST	Move on to Step 10	The clutch is dragging.	Replace the clutch mechanism    Op. 1810A28 CLUTCH - R R FOR MANUAL GEARBOX WITH HYDRAULIC SELECTION VERSIONS
10	BRAKE PEDAL SWITCH CHECK	All OK	Problems encountered	Operation
	Check that the brake pedal switch is working properly	Move on to Step 11	The brake pedal switch is not working properly.	Check the switch on the brake pedal, its fastening, its positioning, the wiring and the engine management control unit. Restore/replace the part that is not working.
11	CORRECT OPERATION CHECK	All OK	Problems encountered	Operation
	Check that the fault is no longer present.	End of diagnosis	The fault persists	Contact technical service for further information on the problem