199000586 - 1088B20 ENGINE COOLING RADIATOR - R + R

Removing ( Refitting ) - Position the vehicle on a lift.    Op. 7055B54 UNDER ENGINE PROTECTION/GUARD - R.R.     Op. 0010T20 ENGINE COOLANT - CHANGE     Op. 0010T84 COOLANT FOR AIR CONDITIONING SYSTEM - DEHYDRATE AND REPRESSURIZE     Op. 7210E10 R.R. FRONT BUMPER     Op. 7210A18 R.R FRONT CROSSMEMBER     Op. 1088B10 ENGINE COOLANT SUPPLY RESERVOIR - R.R.     Op. 1048A23 COLD AIR INTAKE FOR AIR FILTER - R.R 1. Adjust the retaining clips, remove the Waste-Gate solenoid from the fan mounting and place to one side.
1. Disconnect the rapid connector and move the radiator coolant inlet pipe to one side.
1. Disconnect the resistor electrical connection.
DescriptionConnector
1Engine fan adjustment resistance - 1    See O010 ENGINE FAN ADJUSTMENT RESISTANCE - 1
2. Detach the electrical connection for the fan.
DescriptionConnector
2Fan motor    See N011 FAN MOTOR
1. Loosen the band and disconnect the radiator lower coolant outlet hose.
    Op. 1048B17 HEAT EXCHANGER AIR INLET HOSE - R.R.    Op. 1048B32 AIR SUPPLY PIPE ON HEAT EXCHANGER - R.R. 1. Undo bolts (1a) and remove radiator assembly (1b).
1. Undo bolts (1a) fixing air duct (1b) to the heat exchanger (intercooler).2. Compress clips (2a) and adjust points (2b) shown in the figure with a screwdriver to remove air ducts (1b).
1. Undo the bolts fixing the heat exchanger to the radiator.2. Undo the bolts fixing the air conditioning condenser to the radiator.3. Compress the clip and remove the air conditioning condenser.4. Compress clip (4a) and remove heat exchanger (4b).
1. Open retaining clips (1a), loosen band and remove system supply pipe (1b) from the radiator.2. Undo the bolts (2a) and remove the fan (2b) completely from radiator (2c).
Refitting ( Removing ) - Place the fan back in its housing and fasten it to the radiator using the bolts.- Connect the system supply pipe to the radiator and secure with the band and retaining clips.- Refit the air conditioner condenser in its housing, secure the retaining clips and tighten the bolts securing it to the radiator.- Refit the heat exchanger in its housing, secure the retaining clips and tighten the bolts securing it to the radiator.- Replace the air ducts in their housing, securing them to the radiator with the retaining clips.- Tighten the air duct retaining bolts fixing to the heat exchanger (intercooler).- Refit the radiator assembly in its housing until the pins enter their respective flexible mountings on the front, tighten the associated bolts.    Op. 1048B32 AIR SUPPLY PIPE ON HEAT EXCHANGER - R.R.    Op. 1048B17 HEAT EXCHANGER AIR INLET HOSE - R.R.- Connect the coolant outlet pipe to the radiator and tighten the band.- Secure the fan electrical connection.- Connect the resistor electrical connection.- Place the radiator coolant inlet pipe back in its housing and connect rapid connector.- Refit the Waste-Gate solenoid in its housing on the fan mounting and fasten the retaining clip.     Op. 1048A23 COLD AIR INTAKE FOR AIR FILTER - R.R     Op. 1088B10 ENGINE COOLANT SUPPLY RESERVOIR - R.R.     Op. 7210A18 R.R FRONT CROSSMEMBER     Op. 7210E10 R.R. FRONT BUMPER     Op. 0010T84 COOLANT FOR AIR CONDITIONING SYSTEM - DEHYDRATE AND REPRESSURIZE     Op. 0010T20 ENGINE COOLANT - CHANGE     Op. 7055B54 UNDER ENGINE PROTECTION/GUARD - R.R. - Remove the vehicle from the lift.