2584361 - 1056B90 system cable bundle - r + r

Removing ( Refitting ) - Position the vehicle on a lift.- Disconnect the negative battery terminal.    Op. 1048A10 AIR FILTER ASSEMBLY - R.R.1. Disconnect the electrical connection for the Lambda sensor upstream of the catalytic converter.
DescriptionConnector
1Lambda sensor on catalyzer    See K017 LAMBDA SENSOR ON CATALYZER
2. Disconnect the electrical connection for the Lambda sensor downstream of the catalytic converter.
DescriptionConnector
2Lambda sensor on catalyzer    See K017 LAMBDA SENSOR ON CATALYZER
1. Disconnect the intermediate engine wiring coupling.
DescriptionConnector
1Engine cables/engine services cable coupling    See D029 ENGINE CABLES/ENGINE SERVICES CABLE COUPLING
2. Connect the electrical connection for the injection control unit.
DescriptionConnector
2Engine management control unit    See M010 ENGINE MANAGEMENT ECU
3. Undo the nut and disconnect the earth lead from the injection control unit mount.
DescriptionConnector
3Injection control unit earth    See C060 INJECTION CONTROL UNIT EARTH
4. Disconnect the electrical connection for the timing sensor.
DescriptionConnector
4Timing sensor    See K047 TIMING SENSOR
1. Disconnect the electrical connection from the ignition coil module.
DescriptionConnector
1Ignition coil    See A030 IGNITION COIL
2. Disconnect the intermediate injector wiring coupling.
DescriptionConnector
2Injector coupling    See D081 INJECTOR COUPLING
1. Disconnect the electrical connection for the throttle casing.
DescriptionConnector
1Integrated throttle casing actuator    See N075 INTEGRATED THROTTLE CASING ACTUATOR
1. Disconnect the electrical connection for the engine coolant temperature sensor.
DescriptionConnector
1Engine coolant temperature sensor/sender unit    See K036 ENGINE COOLANT TEMPERATURE SENSOR/SENDER UNIT
1. Disconnect the electrical connection of the fuel vapour flow enablement solenoid valve.
DescriptionConnector
1Fuel vapour recovery solenoid valve    See L010 FUEL VAPOUR RECOVERY SOLENOID VALVE
1. Disconnect the electrical connection for the atmospheric pressure sensor.
DescriptionConnector
1Absolute pressure sensor    See K048 ABSOLUTE PRESSURE SENSOR
2. Disconnect the electrical connection for the air temperature/pressure sensor.
DescriptionConnector
2Air pressure - temperature sensor    See K044 AIR PRESSURE - TEMPERATURE SENSOR
1. Disconnect the electrical connection for the variable valve timing solenoid.
DescriptionConnector
1Variable valve timing actuatorSee N076 PHASE TRANSFORMER ACTUATOR
1. Disconnect the electrical connection for the rpm sensor.
DescriptionConnector
1Rpm sensor    See K046 RPM SENSOR
2. Disconnect the electrical connection for the minimum engine oil pressure switch.
DescriptionConnector
2Insufficient engine oil pressure sensor    See K030 INSUFFICIENT ENGINE OIL PRESSURE SENSOR
1. Undo the bolt and remove the earth lead from the engine block.
DescriptionConnector
1Earth on engine    See C040 EARTH ON ENGINE
2. Open the protective cover (2a), undo the nut (2b) and disconnect the starter motor electrical connections (2c).
DescriptionConnector
2cStarter motor    See A020 STARTER MOTOR
3. Disconnect the electrical connection for the detonation sensor.
DescriptionConnector
3Detonation sensor - 2    See K050 DETONATION SENSOR
1. Undo the nut and disconnect the alternator earth lead.
DescriptionConnector
1Alternator    See A010 ALTERNATOR
- Remove the engine wiring harness. Refitting ( Removing ) - Place the wiring harness in its seat.- Connect the earth lead to the alternator.- Connect the electrical connection for the detonation sensor.- Connect the electrical connections for the starter motor, tighten the nut and close the protective cover.- Connect the earth lead to the engine block.- Connect the electrical connection for the minimum engine oil pressure switch.- Connect the electrical connection for the rpm sensor.- Connect the electrical connection for the variable valve timing solenoid.- Connect the electrical connection for the air temperature/pressure sensor.- Connect the electrical connection for the atmospheric pressure sensor.- Connect the electrical connection of the fuel vapour flow enablement solenoid valve.- Connect the engine coolant temperature sensor electrical connection.- Connect the electrical connection for the throttle casing.- Connect the intermediate injector wiring coupling.- Connect the electrical connection of the ignition coil module.- Connect the electrical connection for the timing sensor.- Connect the injection control unit earth lead.- Connect the electrical connection for the injection control unit.- Connect the intermediate engine wiring coupling.- Connect the electrical connection for the Lambda sensor downstream of the catalytic converter.- Connect the electrical connection for the Lambda sensor upstream of the catalytic converter.    Op. 1048A10 AIR FILTER ASSEMBLY - R.R.- Connect the negative battery terminal.- Remove the vehicle from the lift.