2584167 - 1016C10 cylinder head - r + r and replace gasket

Removing ( Refitting )

If the cylinder head is replaced, run the following self-learing procedure.Start up the engine without pressing the accelerator pedal with an engine temperature greater than or equal to 20 °C and idle the engine for 10 seconds

    Op. 1048A10 AIR FILTER ASSEMBLY - R.R.    Op. 1056B82 INJECTION/IGNITION SYSTEM E.C.U. (ONE) - R + R    Op. 1056B87 IGNITION/INJECTION SYSTEM CONTROL UNIT SUPPORT - R.R.    Op. 5510C14 IGNITION COIL/S - R+R    Op. 7055B54 PROTECTION/GUARD UNDER ENGINE - R.R.    Op. 7055B91 RIGHT FRONT WHEEL ARCH LINER - R.R.    Op. 1032D26 TIMING SYSTEM FRONT PROTECTIVE COVER (UPPER PART) - R.R.    Op. 1072C44 EXHAUST MANIFOLD HEAT SHIELD R+R    Op. 1072C16 EXHAUST MANIFOLD WITH CATALYTIC CONVERTER - R R    Op. 0010T20 ENGINE COOLANT - CHANGE    Op. 1092C10 POWER STEERING AND/OR SELF-LEVELLING SUSPENSION PUMP DRIVE BELT - R + R    Op. 1092B60 ALTERNATOR DRIVE BELT - R + R    Op. 1092A10 CRANKSHAFT PULLEY - R + R    Op. 1032D27 TIMING SYSTEM FRONT PROTECTIVE COVER (LOWER PART) - R.R.    Op. 1008B10 FLEXIBLE MOUNTING FOR POWER UNIT FRONT SUPPORT (TIMING SIDE) - REPLACE    Op. 1008A46 TIMING SIDE POWER UNIT RIGID SUPPORT -R.R.    Op. 1032B10 TOOTHED TIMING BELT - R + R FOR TIMING ADJUSTMENT OR REPLACEMENT    Op. 1016A20 SINGLE TAPPET COVER -R.R AND REPLACE GASKET- Position an arm lift underneath the engine.1. Disconnect the check valve from the brake servo. 1. Disconnect the electrical connection for the absolute pressure sensor.

	Description	Connector
1	Absolute pressure sensor	See K048 ABSOLUTE PRESSURE SENSOR

2. Disconnect the electrical connection for the air temperature/pressure sensor.

	Description	Connector
2	Air pressure - temperature sensor	See K44 AIR PRESSURE/TEMPERATURE SENSOR

3. Disconnect the intermediate rapid connector for the fuel vapour pipe. 1. Disconnect the injector wiring junction.

	Description	Connector
1	Injector coupling	See D081 INJECTOR COUPLING

2. Disconnect the electrical connection for the throttle casing.

	Description	Connector
2	Integrated throttle casing actuator	See N075 THROTTLE BODY ACTUATOR

3. Connect the electrical connection to the fuel vapour solenoid valve.

	Description	Connector
3	Fuel vapour recovery solenoid valve	See L010 FUEL VAPOUR RECOVERY SOLENOID

4. Disconnect the fuel pipe rapid connector. 1. Disconnect the electrical connection for the air temperature sensor.

	Description	Connector
1	Engine coolant temperature sensor/sender unit	See K036 ENGINE COOLANT TEMPERATURE SENSOR/SENDER UNIT

2. Loosen collar (2a) and disconnect the water delivery sleeve to radiator (2b).3. Loosen collar (3a) and disconnect the water delivery sleeve to heater (3b).4. Disconnect the degassing pipe rapid connector. 1. Undo the bolts (1a) and remove the cylinder head assembly (1b). - Remove the cylinder head gasket.1. Position the cylinder head in the vice using the tool.

	Description	Code	Function
1	Support	1.860.470.000	Head overhaul

2. Undo the nuts (2a), bolt (2b) and remove the intake manifold (2c). - To finish removing the heat levelling components, refer to    Op. 1016E10 SINGLE CYLINDER HEAD, REMOVED - OVERHAUL Refitting ( Removing ) - Clean the contact surfaces between the cylinder head and engine block.- Position the cylinder head gasket on the cylinder block/crankcase.1. Fit the cylinder head and tighten the fixing bolts to the recommended torque.

	Value daNm	Fastening	Component	dia
-	2.9 ÷ 3.1 + 90° + 90° +/- 3°	Bolt	Cylinder head	M9

Follow the order illustrated below for the tightening of the cylinder head bolts.

- Replace the intake manifold in its housing and secure it by tightening the nuts and bolt to the recommended torque.

	Value daNm	Fastening	Component	dia
-	2.3 ÷ 2.8	Nut	Intake manifold	M8

	Value daNm	Fastening	Component	dia
-	2.3 ÷ 2.8	Bolt	Intake manifold	M8

- Connect the degassing pipe rapid connector.- Connect the water supply pipe to the heater.- Connect the water supply pipe to the radiator.- Connect the electrical connection for the coolant temperature sensor.- Connect the fuel pipe rapid connector.- Connect the electrical connection to the fuel vapour solenoid valve.- Connect the electrical connection for the throttle casing.- Connect the injector wiring junction.- Connect the intermediate rapid connector for the fuel vapour pipe.- Connect the electrical connection for the air temperature/pressure sensor.- Connect the electrical connection for the absolute pressure sensor.- Connect the check valve from the brake servo.- Remove the hydraulic jack from underneath the engine.    Op. 1016A20 SINGLE TAPPET COVER -R.R AND REPLACE GASKET    Op. 1032B10 TOOTHED TIMING BELT - R + R FOR TIMING ADJUSTMENT OR REPLACEMENT    Op. 1008A46 TIMING SIDE POWER UNIT RIGID SUPPORT -R.R.    Op. 1008B10 FLEXIBLE MOUNTING FOR POWER UNIT FRONT SUPPORT (TIMING SIDE) - REPLACE    Op. 1032D27 TIMING SYSTEM FRONT PROTECTIVE COVER (LOWER PART) - R.R.    Op. 1092A10 CRANKSHAFT PULLEY - R + R    Op. 1092B60 ALTERNATOR DRIVE BELT - R + R    Op. 1092C10 POWER STEERING AND/OR SELF-LEVELLING SUSPENSION PUMP DRIVE BELT - R + R    Op. 1072C16 EXHAUST MANIFOLD WITH CATALYTIC CONVERTER - R R    Op. 1072C44 EXHAUST MANIFOLD HEAT SHIELD R+R    Op. 1032D26 TIMING SYSTEM FRONT PROTECTIVE COVER (UPPER PART) - R.R.    Op. 7055B91 RIGHT FRONT WHEEL ARCH LINER - R.R.    Op. 7055B54 PROTECTION/GUARD UNDER ENGINE - R.R.    Op. 5510C14 IGNITION COIL/S - R+R    Op. 1056B87 IGNITION/INJECTION SYSTEM CONTROL UNIT SUPPORT - R.R.    Op. 1056B82 INJECTION/IGNITION SYSTEM E.C.U. (ONE) - R + R    Op. 1048A10 AIR FILTER ASSEMBLY - R.R.    Op. 0010T20 ENGINE COOLANT - CHANGE