2584361 - 1056B90 system cable bundle - r + r

Removing ( Refitting ) - Position the vehicle on a lift.- Disconnect the negative battery terminal.    Op. 1048A10 AIR FILTER ASSEMBLY - R.R.1. Disconnect the electrical connection for the Lambda sensor upstream of the catalytic converter.

	Description	Connector
1	Lambda sensor on catalyzer	See K017 LAMBDA SENSOR ON CATALYZER

2. Disconnect the electrical connection for the Lambda sensor downstream of the catalytic converter.

	Description	Connector
2	Lambda sensor on catalyzer	See K017 LAMBDA SENSOR ON CATALYZER

1. Disconnect the intermediate engine wiring coupling.

	Description	Connector
1	Engine cables/engine services cable coupling	See D029 ENGINE CABLES/ENGINE SERVICES CABLE COUPLING

2. Connect the electrical connection for the injection control unit.

	Description	Connector
2	Engine management control unit	See M010 ENGINE MANAGEMENT ECU

3. Undo the nut and disconnect the earth lead from the injection control unit mount.

	Description	Connector
3	Injection control unit earth	See C060 INJECTION CONTROL UNIT EARTH

4. Disconnect the electrical connection for the timing sensor.

	Description	Connector
4	Timing sensor	See K047 TIMING SENSOR

1. Disconnect the electrical connection from the ignition coil module.

	Description	Connector
1	Ignition coil	See A030 IGNITION COIL

2. Disconnect the intermediate injector wiring coupling.

	Description	Connector
2	Injector coupling	See D081 INJECTOR COUPLING

1. Disconnect the electrical connection for the throttle casing.

	Description	Connector
1	Integrated throttle casing actuator	See N075 INTEGRATED THROTTLE CASING ACTUATOR

1. Disconnect the electrical connection for the engine coolant temperature sensor.

	Description	Connector
1	Engine coolant temperature sensor/sender unit	See K036 ENGINE COOLANT TEMPERATURE SENSOR/SENDER UNIT

1. Disconnect the electrical connection of the fuel vapour flow enablement solenoid valve.

	Description	Connector
1	Fuel vapour recovery solenoid valve	See L010 FUEL VAPOUR RECOVERY SOLENOID VALVE

1. Disconnect the electrical connection for the atmospheric pressure sensor.

	Description	Connector
1	Absolute pressure sensor	See K048 ABSOLUTE PRESSURE SENSOR

2. Disconnect the electrical connection for the air temperature/pressure sensor.

	Description	Connector
2	Air pressure - temperature sensor	See K044 AIR PRESSURE - TEMPERATURE SENSOR

1. Disconnect the electrical connection for the variable valve timing solenoid.

	Description	Connector
1	Variable valve timing actuator	See N076 PHASE TRANSFORMER ACTUATOR

1. Disconnect the electrical connection for the rpm sensor.

	Description	Connector
1	Rpm sensor	See K046 RPM SENSOR

2. Disconnect the electrical connection for the minimum engine oil pressure switch.

	Description	Connector
2	Insufficient engine oil pressure sensor	See K030 INSUFFICIENT ENGINE OIL PRESSURE SENSOR

1. Undo the bolt and remove the earth lead from the engine block.

	Description	Connector
1	Earth on engine	See C040 EARTH ON ENGINE

2. Open the protective cover (2a), undo the nut (2b) and disconnect the starter motor electrical connections (2c).

	Description	Connector
2c	Starter motor	See A020 STARTER MOTOR

3. Disconnect the electrical connection for the detonation sensor.

	Description	Connector
3	Detonation sensor - 2	See K050 DETONATION SENSOR

1. Undo the nut and disconnect the alternator earth lead.

	Description	Connector
1	Alternator	See A010 ALTERNATOR

- Remove the engine wiring harness. Refitting ( Removing ) - Place the wiring harness in its seat.- Connect the earth lead to the alternator.- Connect the electrical connection for the detonation sensor.- Connect the electrical connections for the starter motor, tighten the nut and close the protective cover.- Connect the earth lead to the engine block.- Connect the electrical connection for the minimum engine oil pressure switch.- Connect the electrical connection for the rpm sensor.- Connect the electrical connection for the variable valve timing solenoid.- Connect the electrical connection for the air temperature/pressure sensor.- Connect the electrical connection for the atmospheric pressure sensor.- Connect the electrical connection of the fuel vapour flow enablement solenoid valve.- Connect the engine coolant temperature sensor electrical connection.- Connect the electrical connection for the throttle casing.- Connect the intermediate injector wiring coupling.- Connect the electrical connection of the ignition coil module.- Connect the electrical connection for the timing sensor.- Connect the injection control unit earth lead.- Connect the electrical connection for the injection control unit.- Connect the intermediate engine wiring coupling.- Connect the electrical connection for the Lambda sensor downstream of the catalytic converter.- Connect the electrical connection for the Lambda sensor upstream of the catalytic converter.    Op. 1048A10 AIR FILTER ASSEMBLY - R.R.- Connect the negative battery terminal.- Remove the vehicle from the lift.