2584612 - 2710A40 l/h or r/h drive shaft (one) - r + r

Removing ( Refitting ) Place the car on a ramp.    Op. 4450B02 LEFT FRONT WHEEL - R.R.Raise the lift.    Op. 7055B54 PROTECTION/GUARD UNDER ENGINE - R.R.Place a suitable bowl under the car to collect the gearbox oil.1. Undo the plug on the gearbox and drain the gearbox oil. 1. Using a hammer and suitable chisel, relieve the staking on ad then undo the wheel hub nut.2. Undo the bolts securing the shock absorber strut.3. Undo the fixing nut (3a) and using the tool (3b), remove the steering balljoint head from the vertical link.

	Name	Country
3b	Head extractor	1.847.035.000

1. Tilt the brake disc/wheel hub assembly downwards.Disengage and withdraw the drive shaft from the hub.2. Open the clip securing the drive shaft to the differential.3. Remove the drive shaft complete with constant velocity joint and tripod joint. Refitting ( Removing ) Check the drive shaft for damage.Check that the gaiters are not damaged and that they contain lubricating grease.Engage the tripod joint on the differential.Lock the drive shaft on the flange using a new clip.Engage the constant velocity joint on the wheel hub.Refit the brake disc/wheel hub assembly in its seating.Tighten the bolts securing the shock absorber strut to the specified torque.

	Fastening	Component	Ø	Value(daNm)
-	Nut	FRONT DAMPER	M10 x 1.25	(Steering knuckle side) 12

Fit the steering tie-rod end in its seating.Tighten the nut to the specified torque.

	Fastening	Component	Ø	Value(daNm)
-	Nut	FRONT SUSPENSION LOWER LEVER BALL JOINT	M10 x 1.25	6

Tighten the wheel hub nut to torque.

	Fastening	Component	Ø	Value(daNm)
-	Nut	FRONT HUB WITH BEARINGS	M22	7 + 55°

1. Stake the nut in accordance with the illustration below. Replace the oil drain plug seal.Screw on the gearbox oil plug and tighten it to the specified torque.

	Fastening	Component	Ø	Value(daNm)
-	Plug	GEAR CASING PADS	M22 x 1.5	3.6

Insert oil into the gearbox.

	Type	Component	Name	Qty.
-	Oil	GEARBOX OIL	TUTELA CAR ZC 75 Synth	-

Check the oil level.    Op. 4450B02 LEFT FRONT WHEEL - R.R.    Op. 7055B54 PROTECTION/GUARD UNDER ENGINE - R.R.Remove the vehicle from the ramp.

The operation of removing and refitting the left driveshaft is described and illustrated below; the right driveshaft is removed and refitted in a similar way bearing in mind that it is connected to the intermediate driveshaft rather than to the differential internal driveshaft.

Removing ( Refitting ) Position the vehicle on the ramp.Proceed with the removal    Op. 7055B54 PROTECTION/GUARD UNDER ENGINE - R.R..Proceed with the removal    Op. 4450B02 LEFT FRONT WHEEL - R.R..1. Remove the bevel and undo the nut fixing the driveshaft to the wheel hub. 1. Undo the nut (1a) and disconnect the steering rod (1b) from the steering knuckle using the tool (1c).

	Name	Country
1c	Head extractor	1.847.035.000

Release the driveshaft from the wheel hub.1. Loosen the band (1a), then remove the driveshaft complete with joints (1b). Refitting ( Removing ) Refit the drive shaft complete with couplings in its seating.Tighten the band.1. Connect the steering link (1a) to the front steering knuckle and tighten the nut (1b) to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1b	Nut	POWER STEERNG BOX LINKS	M10	(Wheel damper side) 4.5 ÷ 5.5

1. Tighten the nut (1a) securing the front wheel hub to the drive shaft to the recommended torque, using the angle tightening tool (1b).

	Fastening	Component	Ø	Value(daNm)
1a	Nut	DRIVESHAFT	M22	(Wheel hub side) 7.0 + 55°

	Name	Country
1b	Protractor	1.860.942.000

1. Bevel the collar of the nut in two places as shown in the figure. Proceed with the refitting    Op. 4450B02 LEFT FRONT WHEEL - R.R..Proceed with the refitting    Op. 7055B54 PROTECTION/GUARD UNDER ENGINE - R.R..Remove the car from the ramp.