2584888 - 5505B43 wiring built into load compartment left rear door flap r r with interfering parts removed
 Removing
		(
		Refitting
Removing
		(
		Refitting )
	1. Disconnect the electrical connectors (1a), (1b), (1c), (1d), (1e), (1f), and (1g).
		)
	1. Disconnect the electrical connectors (1a), (1b), (1c), (1d), (1e), (1f), and (1g).|  | Name | Connector | 
|---|---|---|
| 1a | Tailgate rear seal/ | See D085 TAILGATE/REAR SEAL | 
| Name | Connector | |
|---|---|---|
| 1b | Left number plate light | See F050 LEFT NUMBER PLATE LIGHT | 
| Name | Connector | |
|---|---|---|
| 1b | Right number plate light | See F51 RIGHT NUMBER PLATE LIGHT ( LEFT TAILGATE ) | 
| Name | Connector | |
|---|---|---|
| 1c | Switch on rear door | See I21 SWITCH ON REAR DOOR ( LEFT TAILGATE ) | 
| Name | Connector | |
|---|---|---|
| 1d | Rear door lock geared motor | See N52 REAR DOOR LOCK GEARED MOTOR ( LEFT TAILGATE ) | 
| Name | Connector | |
|---|---|---|
| 1e | Additional (third brake light) | See F40 ADDITIONAL (THIRD BRAKE LIGHT) ( LEFT TAILGATE ) | 
| Name | Connector | |
|---|---|---|
| 1f | Left heated rear windscreen | See P054 LEFT HEATED REAR WINDSCREEN | 
|  | Name | Connector | 
|---|---|---|
| 1g | Rear window wiper motor | See N016 REAR WINDOW WIPER MOTOR | 

|  | Before removing the electrical wiring from the housing it is advisable to connect a general sensor to each individual connector so that it retraces the route of the section of wiring removed. This operation makes it possible, during the refitting stage, to restore the correct routing of the wiring removed. | 
 Refitting
		(
		Removing
Refitting
		(
		Removing )
	Check that the wiring is not damaged.If necessary, check the continuity.Connect each individual electrical connector to the sensor used previusly in order to facilitate the routing of the section of cable removed in its original position.Pull the end of the sensor and restore the routing of the electrical wiring.Carry out the same operation for all the electrical connectors.Position the electrical wiring, securing it using new retaining bands.Disconnect each individual electrical connector from the sensor.Connect the electrical connectors:
		)
	Check that the wiring is not damaged.If necessary, check the continuity.Connect each individual electrical connector to the sensor used previusly in order to facilitate the routing of the section of cable removed in its original position.Pull the end of the sensor and restore the routing of the electrical wiring.Carry out the same operation for all the electrical connectors.Position the electrical wiring, securing it using new retaining bands.Disconnect each individual electrical connector from the sensor.Connect the electrical connectors:|  | Name | Connector | 
|---|---|---|
| - | Tailgate rear seal/ | See D085 TAILGATE/REAR SEAL | 
|  | Name | Connector | 
|---|---|---|
| - | Left number plate light | See F050 LEFT NUMBER PLATE LIGHT | 
|  | Name | Connector | 
|---|---|---|
| - | Right number plate light | See F51 RIGHT NUMBER PLATE LIGHT ( LEFT TAILGATE ) | 
|  | Name | Connector | 
|---|---|---|
| - | Switch on rear door | See I21 SWITCH ON REAR DOOR ( LEFT TAILGATE ) | 
|  | Name | Connector | 
|---|---|---|
| - | Rear door lock geared motor | See N52 REAR DOOR LOCK GEARED MOTOR ( LEFT TAILGATE ) | 
|  | Name | Connector | 
|---|---|---|
| - | Additional (third brake light) | See F40 ADDITIONAL (THIRD BRAKE LIGHT) ( LEFT TAILGATE ) | 
|  | Name | Connector | 
|---|---|---|
| - | Left heated rear windscreen | See P054 LEFT HEATED REAR WINDSCREEN | 
|  | Name | Connector | 
|---|---|---|
| - | Rear window wiper motor | See N016 REAR WINDOW WIPER MOTOR |