5505C29 INTERGRATED ENGINE BAY AND ABS SYSTEM WIRING - R R WITH FOULING PARTS REMOVED - Fiat - DOBLO - eLearn

2584892 - 5505C29 intergrated engine bay and abs system wiring - r r with fouling parts removed

) Work in the engine compartment.1. Undo the nut (1a) and separate the cable (1b) from the negative battery terminal (1c).2. Disconnect the electrical connectors (2a), (2b), (2c), (2d), (2e), (2f), (2g), (2h), (2i), (2l), (2m), (2n), (2p).

	Name	Connector
2a	Right headlamp	See F011 RIGHT HEADLAMP

	Name	Connector
2b	4 stage pressure switch	See K010 FOUR STAGE PRESSURE SWITCH

	Name	Connector
2c	Windscreen/rearscreen electric washer pump motor	See N22 WINDSCREEN/REARSCREEN ELECTRIC WASHER PUMP MOTOR ( FRONT )

	Name	Connector
2d	Left headlamp	See F010 LEFT HEADLAMP

	Name	Connector
2e	Single-tone horn	See P005 SINGLE-TONE HORN

	Name	Connector
2f	Reversing lights switch	See I20 REVERSING LIGHTS SWITCH ( FRONT )

	Name	Connector
2g	Front left earth	See C010 LEFT FRONT EARTH

	Name	Connector
2h	Windscreen wiper motor	See N015 WINDSCREEN WIPER MOTOR

	Name	Connector
2i	Brake fluid level (switch) sensor	See K025 BRAKE FLUID LEVEL SENSOR (SWITCH)

	Name	Connector
2l	Left front wheel sensor for ABS	See K70 LEFT FRONT WHEEL SENSOR FOR ABS ( FRONT )

	Name	Connector
2m	Right front wheel sensor for ABS	See K071 RIGHT FRONT WHEEL SENSOR FOR ABS

	Name	Connector
2n	ABS control unit	See M50 ABS CONTROL UNIT ( FRONT )

	Name	Connector
2p	Front/engine coupling	See D004 FRONT/ENGINE COUPLING

1. Disconnect the windscreen washer fluid supply pipes (1a) to the windscreen and rearscreen from the electric pump (1b).

Work inside the passenger compartment and remove the front carpet, in the area of the centre pillar, to gain access to the ABS connectors.1. Disconnect the electrical connectors (1a), (1b), (1c), (1d), (1e), (1f), (1g), (1h).

	Name	Connector
1a	Right rear wheel sensor for ABS	See K76 RIGHT REAR WHEEL SENSOR FOR ABS ( FRONT )

	Name	Connector
1b	Left rear wheel sensor for ABS	See K75 LEFT REAR WHEEL SENSOR FOR ABS ( FRONT )

	Name	Connector
1c	Front/air conditioning - heater coupling	See D008 FRONT/AIR CONDITIONING - HEATER COUPLING

	Name	Connector
1d	Brake pedal switch	See I30 BRAKE PEDAL SWITCH ( FRONT )

	Name	Connector
1e	Clutch pedal switch	See I31 CLUTCH PEDAL SWITCH ( FRONT )

	Name	Connector
1f	Accelerator pedal potentiometer	See K55 ACCELERATOR PEDAL POTENTIOMETER ( FRONT )

	Name	Connector
1g	Data not available yet

	Name	Connector
1h	Stalk unit	See H005 STEERING COLUMN SWITCH UNIT

	Name	Connector
1i	Ignition switch	See H001 IGNITION SWITCH

1. Undo the fixing nuts (1a) and place the ABS control unit (1b), complete with bracket, to the side.

Release the engine compartment wiring complete with rubber cable duct and windscreen washer fluid supply pipes to the windscreen and rearscreen, releasing them from the retaining bands.

Refitting ( Removing

) Check that the wiring is not damaged and that the individual conductors are firmly attached to the connections.If necessary, check the continuity.Connect a sensor to the wiring and apply vaseline to the edge of the rubber cable duct to facilitate the fitting in the housing.Pass the wiring into the vehicle and then fit the rubber cable duct in place.Connect the windscreen washer fluid supply pipes to the windscreen and rearscreen to the electric pump.Connect the electrical connectors:

	Name	Connector
-	Right rear wheel sensor for ABS	See K76 RIGHT REAR WHEEL SENSOR FOR ABS ( FRONT )

	Name	Connector
-	Left rear wheel sensor for ABS	See K75 LEFT REAR WHEEL SENSOR FOR ABS ( FRONT )

	Name	Connector
-	Front/air conditioning - heater coupling	See D008 FRONT/AIR CONDITIONING - HEATER COUPLING

	Name	Connector
-	Brake pedal switch	See I30 BRAKE PEDAL SWITCH ( FRONT )

	Name	Connector
-	Clutch pedal switch	See I31 CLUTCH PEDAL SWITCH ( FRONT )

	Name	Connector
-	Accelerator pedal potentiometer	See K55 ACCELERATOR PEDAL POTENTIOMETER ( FRONT )

	Name	Connector
-	Aerial for Fiat-CODE	See P91 AERIAL FOR FIAT-CODE ( FRONT )

	Name	Connector
-	Stalk unit	See H005 STEERING COLUMN SWITCH UNIT

	Name	Connector
-	Ignition switch	See H001 IGNITION SWITCH

Reposition the front carpet.Work in the engine compartment and connect the electrical connectors.

	Name	Connector
-	Right headlamp	See F011 RIGHT HEADLAMP

	Name	Connector
-	4 stage pressure switch	See K010 FOUR STAGE PRESSURE SWITCH

	Name	Connector
-	Windscreen/rearscreen electric washer pump motor	See N22 WINDSCREEN/REARSCREEN ELECTRIC WASHER PUMP MOTOR ( FRONT )

	Name	Connector
-	Left headlamp	See F010 LEFT HEADLAMP

	Name	Connector
-	Single-tone horn	See P005 SINGLE-TONE HORN

	Name	Connector
-	Reversing lights switch	See I20 REVERSING LIGHTS SWITCH ( FRONT )

	Name	Connector
-	Front left earth	See C010 LEFT FRONT EARTH

	Name	Connector
-	Windscreen wiper motor	See N015 WINDSCREEN WIPER MOTOR

	Name	Connector
-	Brake fluid level (switch) sensor	See K025 BRAKE FLUID LEVEL SENSOR (SWITCH)

	Name	Connector
-	Left front wheel sensor for ABS	See K70 LEFT FRONT WHEEL SENSOR FOR ABS ( FRONT )

	Name	Connector
-	Right front wheel sensor for ABS	See K071 RIGHT FRONT WHEEL SENSOR FOR ABS

	Name	Connector
-	ABS control unit	See M50 ABS CONTROL UNIT ( FRONT )

	Name	Connector
-	Front/engine coupling	See D004 FRONT/ENGINE COUPLING

Secure the front wiring using new retaining bands, checking that there is no interference with the surrounding components.Position the ABS control unit and secure it tightening the nuts to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
-	Bolt	HYDRAULIC AND ELECTRONIC CONTROL UNIT	M8	2.5