5505C40 CABIN WIRIRNG - R R - Fiat - DOBLO - eLearn

2584895 - 5505C40 cabin wirirng - r r

) Place the car on a ramp.1. Position an appropriate stand beneath the tank in order to support it.2. Undo the tank bracket retaining bolts.3. Lower the tank (3a) and disconnect the electrical connector (3b).

	Name	Connector
3b	EPIC injection pump	See N41 EPIC INJECTION PUMP

Release the section of wiring to the electric pump from the retaining bands and remove it.Refit the tank back in position and screw in the bracket fixing bolts without tightening them to torque.Lower the lift and remove the car.1. Disconnect the electrical connections (1a), (1b), (1c), (1d), (1e), (1f), (1g), (1h), driver''s side and passenger side.

	Name	Connector
1a	Switch on left front door	See I016 SWITCH ON LEFT FRONT DOOR.

	Name	Connector
1a	Switch on right front door	See I017 SWITCH ON RIGHT FRONT DOOR

	Name	Connector
1b	Front left door connection	See D30 FRONT LEFT DOOR CONNECTION ( REAR )

	Name	Connector
1b	Front right door connection	See D031 REAR/PASSENGER FRONT DOOR COUPLING

	Name	Connector
1c	Sensor for driver''s, Side Bag	See K66 SENSOR FOR DRIVER'S, SIDE BAG ( REAR )

	Name	Connector
1c	Passenger , Side Bag sensor	See K067 SENSOR FOR PASSENGER SIDE BAG

	Name	Connector
1d	Driver''s seat belt pre-tensioner	See Q20 DRIVER'S SEAT BELT PRE-TENSIONER ( REAR )

	Name	Connector
1d	Front passenger seat belt pre-tensioner	See Q21 FRONT PASSENGER SEAT BELT PRE-TENSIONER ( REAR )

	Name	Connector
1e	Sensor for driver''s, Side Bag	See K66 SENSOR FOR DRIVER'S, SIDE BAG ( REAR )

	Name	Connector
1e	Passenger , Side Bag sensor	See K067 SENSOR FOR PASSENGER SIDE BAG

	Name	Connector
1f	Rear left door connection	See D35 REAR/LEFT REAR DOOR COUPLING

	Name	Connector
1f	Rear right door connection	See D36 REAR/RIGHT REAR DOOR COUPLING

	Name	Connector
1g	Rear left loudspeaker (in parcel shelf)	See P030 LEFT REAR SPEAKER

	Name	Connector
1g	Right rear speaker (in parcel shelf)	See P031 RIGHT REAR SPEAKER

	Name	Connector
1h	Tailgate rear seal/	See D085 TAILGATE/REAR SEAL

1. Disconnect the electrical connectors (1a), (1b), (1c), (1d), (1e), (1f), (1g), (1h), (1i),(1l), (1m), (1n).

	Name	Connector
1a	Facia earth, driver''s side	See C015 DASHBOARD EARTH, DRIVER'S SIDE

	Name	Connector
1b	Left rear earth	See C30 LEFT REAR EARTH ( REAR )

	Name	Connector
1c	Left seat heater	See O40 LEFT SEAT HEATER ( REAR )

	Name	Connector
1d	Handbrake "on" switch	See I40 HANDBRAKE "ON" SWITCH ( REAR )

	Name	Connector
1e	Short circuiting coupling	See D097 SHORT CIRCUITING COUPLING

	Name	Connector
1f	Dashboard/rear coupling	See D20 DASHBOARD/REAR COUPLING ( REAR )

	Name	Connector
1g	Inertia switch	See I50 INERTIA SWITCH ( REAR )

	Name	Connector
1h	Front courtesy light	See G10 FRONT COURTESY LIGHT ( REAR )

	Name	Connector
1i	Air Bag control unit	See M060 AIR BAG CONTROL UNIT

	Name	Connector
1l	Side Bag + Head Bag earth	See C053 SIDE BAG + HEAD BAG EARTH

	Name	Connector
1m	Boot courtesy light	See G040 BOOT COURTESY LIGHT

	Name	Connector
1n	Rear (centre courtesy light)	See G20 REAR (CENTRE COURTESY LIGHT) ( REAR )

Release the electrical wiring from the securing bands.

Before removing the electrical wiring from the housing it is advisable to connect a general sensor to each individual connector so that the routing of the section of cable removed can be retraced. This operation makes it possible, when refitting, to restore the correct routing of the wiring removed.

Remove the electrical wiring and release each individual connector from the sensor connected to it.

Refitting ( Removing

) Check that the wiring is undamaged and that the individual conductors are firmly attached to the connections.If necessary, check the continuity.Connect each individual connector to the sensor used previously in order to facilitate the routing of the section of cable removed in its original position.Pull the end of the sensor and restore the routing of the electrical wiring.Carry out the same operation for all the electrical connectors for the rear wiring.Position the rear electrical wiring, securing it using the new retaining bands.Disconnect each individual electrical connector from the sensor.Connect the electrical connectors:

	Name	Connector
-	Facia earth, driver''s side	See C015 DASHBOARD EARTH, DRIVER'S SIDE

	Name	Connector
-	Left rear earth	See C30 LEFT REAR EARTH ( REAR )

	Name	Connector
-	Left seat heater	See O40 LEFT SEAT HEATER ( REAR )

	Name	Connector
-	Handbrake "on" switch	See I40 HANDBRAKE "ON" SWITCH ( REAR )

	Name	Connector
-	Short circuiting coupling	See D097 SHORT CIRCUITING COUPLING

	Name	Connector
-	Dashboard/rear coupling	See D20 DASHBOARD/REAR COUPLING ( REAR )

	Name	Connector
-	Inertia switch	See I50 INERTIA SWITCH ( REAR )

	Name	Connector
-	Front courtesy light	See G10 FRONT COURTESY LIGHT ( REAR )

	Name	Connector
-	Air Bag control unit	See M060 AIR BAG CONTROL UNIT

	Name	Connector
-	Side Bag + Head Bag earth	See C053 SIDE BAG + HEAD BAG EARTH

	Name	Connector
-	Boot courtesy light	See G040 BOOT COURTESY LIGHT

	Name	Connector
-	Rear (centre courtesy light)	See G20 REAR (CENTRE COURTESY LIGHT) ( REAR )

Connect the electrical connectors, carrying out the operation on both the driver and passenger sides:

	Name	Connector
1a	Switch on left front door	See I016 SWITCH ON LEFT FRONT DOOR.

	Name	Connector
1a	Switch on right front door	See I017 SWITCH ON RIGHT FRONT DOOR

	Name	Connector
1b	Front left door connection	See D30 FRONT LEFT DOOR CONNECTION ( REAR )

	Name	Connector
1b	Front right door connection	See D031 REAR/PASSENGER FRONT DOOR COUPLING

	Name	Connector
1c	Sensor for driver''s, Side Bag	See K66 SENSOR FOR DRIVER'S, SIDE BAG ( REAR )

	Name	Connector
1c	Passenger , Side Bag sensor	See K067 SENSOR FOR PASSENGER SIDE BAG

	Name	Connector
1d	Driver''s seat belt pre-tensioner	See Q20 DRIVER'S SEAT BELT PRE-TENSIONER ( REAR )

	Name	Connector
1d	Front passenger seat belt pre-tensioner	See Q21 FRONT PASSENGER SEAT BELT PRE-TENSIONER ( REAR )

	Name	Connector
1e	Sensor for driver''s, Side Bag	See K66 SENSOR FOR DRIVER'S, SIDE BAG ( REAR )

	Name	Connector
1e	Passenger , Side Bag sensor	See K067 SENSOR FOR PASSENGER SIDE BAG

	Name	Connector
1f	Rear left door connection	See D35 REAR/LEFT REAR DOOR COUPLING

	Name	Connector
1f	Rear right door connection	See D36 REAR/RIGHT REAR DOOR COUPLING

	Name	Connector
1g	Rear left loudspeaker (in parcel shelf)	See P030 LEFT REAR SPEAKER

	Name	Connector
1g	Right rear speaker (in parcel shelf)	See P031 RIGHT REAR SPEAKER

	Name	Connector
1h	Tailgate rear seal/	See D085 TAILGATE/REAR SEAL

Place the car on a ramp.Raise the ramp.Position an appropriate stand beneath the tank in order to support it.Tighten the bolts fixing the tank brackets.Lower the tank, connect the electrical connector to the electric pump and secure the section of wiring using new retaining bands.

	Name	Connector
3b	EPIC injection pump	See N41 EPIC INJECTION PUMP

Refit the tank in place and tighten the bracket fixing bolts to torque.

	Fastening	Component	Ø	Value(daNm)
-	-	-	-	-

Remove the tool used for refitting the tank.Lower the lift and remove the car.