244000439 - AIR BAG SYSTEM
COMPOSITION
The vehicle is equipped with a frontal and side (optional) protection system which is activated following impacts of medium intensity to ensure the safety of the occupants of the front seats. To complete the safety system and to improve the restraint system the vehicle is also fitted with front seat belt pretensioners with load restricters. The control unit control system allwos the total or partial activation of the devices in the case of a frontal impact.The (Breed) protection system comprises:- 3 pretensioners, driver's, front side passenger and front centre passenger, respectively;
- A driver's Air Bag;
- A passenger Air Bag (with the task of protecting the front passenger and the centre front passenger);
- 2 side impact sensors (one on each side)
- A passenger Air Bag disabling switch
- 2 side Air Bags (side bags, one on each side)
ELECTRONIC CONTROL UNIT
| 1 | Earth |
|---|---|
| 2 | Not used |
| 3 | Not used |
| 4 | Not used |
| 5 | Crash output (not currently used on the Ducato) |
| 6 | Diagnostic serial line K |
| 7 | Passenger air bag disabled warning light (where fitted) |
| 8 | Bulb failure |
| 9 | Not used |
| 10 | Switch for disabling passenger Air Bag (-) (where fitted) |
| 11 | Switch for disabling passenger Air Bag (+) (where fitted) |
| 12 | Supply from ignition (+15) |
| 13 | Not used |
| 14 | Not used |
| 15 | Not used |
| 16 | Not used |
| 17 | passenger air bag 2nd stage (+) |
| 18 | passenger air bag 2nd stage (-) |
| 19 | Not used |
| 20 | Not used |
| 21 | passenger air bag 1st stage (+) |
| 22 | passenger air bag 1st stage (-) |
| 23 | Driver's air bag (+) |
| 24 | Driver's air bag (-) |
| 1 | Driver's pretensioner (-) |
|---|---|
| 2 | Driver's pretensioner (+) |
| 3 | Passenger pretensioner (-) |
| 4 | Passenger pretensioner (+) |
| 5 | Driver's side bag or centre pretensioner (-) |
| 6 | Driver's side bag or centre pretensioner (+) |
| 7 | Not used |
| 8 | Not used |
| 9 | Passenger side bag (-) |
| 10 | Passenger side bag (+) |
| 11 | Not used |
| 12 | Not used |
| 13 | Not used |
| 14 | Not used |
| 15 | Not used |
| 16 | Not used |
| 17 | Earth |
| 18 | Not used |
| 19 | Not used |
| 20 | Not used |
| 21 | Not used |
| 22 | Not used |
| 23 | Not used |
| 24 | Driver's side sensor: Supply + communication |
| 25 | Passenger side sensor: Supply + communication |
| 26 | Driver's side sensor: Earth |
| 27 | Passenger side sensor: Earth |
| 28 | Not used |
| 29 | Not used |
| 30 | Not used |
| 31 | Not used |
| 32 | Earth |
Specifications
The electronic control unit manages the entire system and controls all its components. It is designed to recognise an impact situation in plenty of time to activate the pretensioners alone or the pretensioners plus the air bag modules according to impact severity and type.The control unit is rigidly secured to the body beneath the central car consule near the centre of gravity. This location allows interior deceleration sensors to detect car deceleration with accuracy. | The control unit should always be fitted with the arrow, stamped on the adhesive plate, facing the direction of travel of the vehicle. Always check that there are no foreign bodies between the control unit and the bodyshell and tighten the fixing bolts to the recommended torque. |
Composition
The control unit contains two deceleration sensors, one electronic and one electromechanical safety sensor that activates an activation enablement function independently of the electronic sensor.If the car deceleration level detected by the electronic sensor and processed by the ECU in terms of impact severity, exceeds the severity level set for the device deactivation control, the control unit allows the command to be sent only if the safety sensor is closed at the same moment.The following functions are present to ensure the system is correctly managed:- energy accumulation: the control unit is supplied at 12V with the key ON but can still operate for a few fractions of a second if the power supply is cut off or experiences a voltage drop in order to safeguard system operation and write the data in the crash memory.
- check earth fastening: the control unit software checks the electrical contact between body and control unit;
- fault memory: with the key ON, the control unit continuously monitors circuit operation (including energy reserve circuits) during normal vehicle operation and impacts. It also diagnoses all electrical parts of the system and indicates the presence of faults by turning on an airbag system fault warning light on the instrument panel and saving the fault code.
- crash memory: records information on crash events that trigger activation of the pretensioners and front or side modules.
DRIVER'S AIR BAG MODULE
- a plastic cover that tears at preset points when activated to allow the bag to expand correctly.
- a bag which has a volume of around 60 litres
- a pyrotechnic type gas generator
- a containment case.
Operation
The module gas inflation generator is electrically activated by means of a signal from the electronic control module. Following this signal a pyrotechnic charge housed in the generator is primed. The gases produced by the combustion of the charge flow through special openings and expand in the bag causing the cover to break at specified points. When fully inflated, the bag is in an optimal position to protect the occupant. After the bag is inflated by the gases it immediately deflates thanks to the presence of suitably located breather openings.PASSENGER AIR BAG
Operation
The passenger Air Bag is located in the dashboard and is designed to protect the two front pasengers.It consists of a module comprising two gas generators that have the task of inflating a very large single bag (about 120 litres) whose shape is designed to protect the occupants of both the centre and side seats. This solution allows the optimum protection of both occupants.The composition and operation are the same as for the driver's Air Bag, with with two gas generators in place of the single one for the driver's air bag fitted in the steering wheel.A plastic flap that is incorporated in the dashboard allows the bag to escape as it inflates in the direction of the driver.SATELLITE SENSOR SIDE BAG SYSTEM
Operation
The Side Bag modules are fitted in the door side front seat backrests.To ensure maximum front seat occupant safety in the case of side impact, side bag modules are installed on the seat squabs. They are fitted on the side facing the outside of the car beneath the trim.This configuration is considered one of the most effective because it ensures the airbag is always in optimum position in relation to the occupant regardless of seat setting or occupant size.The side bag mainly protects the chest and abdomen, even if the seat occupant is not sitting properly because bag opening dynamics minimise the risk of body damage caused by impact with the airbag.The side bag module consists of a plastic container that houses the gas generator and a permeable nylon bag.The module container includes a cover with preset break points. When the seat cover is fitted, the exterior of the trim in the area over the bags includes seams designed to yield easily.The connection between the module and the electrical system takes place by means of two cables with a yellow outer casing housed together with the connecting cable. The module inflation gas generator is electrically activated by a signal coming from the electronic control unit. The signal is managed by satellite sensors, located in the centre pillars, which detect direct impact acceleration along the transverse axis of the vehicle and send it to the control unit. Following this signal, a pyrotechnic activation is set off that causes the gas in the generator to expand and inflate the bag.The increase in bag volume breaks the container in the set areas and causes the squab cover seams to yield along the preset sections to allow the bag to emerge correctly. When fully inflated, the bag is in an optimal position to protect the occupant. The bag deflates immediately after being inflated by the gas because the fabric is permeable. | It is not possible to carry out operations on seats fitted with air bags, apart from seat removal/refitting. It is strictly forbidden to dismantle seats fitted with air bags. This operation must be carried by trained, authorised technical personnel. |
| Do not cover the front seat squab with extra covers. |
| Do not wash the seat squab with water or steam under pressure. |
CLOCK SPRING
The clock spring is a device that allows the leads connecting the air bag module and the other electrical controls installed on the steering wheel to follow steering wheel rotation without danger of breaking.The clock spring has two cables on the steering wheel side with one designed to connect the Air Bag module and one for connecting the steering wheel electrical functions.Operation
Inside the two plates, the leads connecting the air bag module are wound into a spiral with sufficient coils to follow the steering wheel rotations. The upper plate is turned by fasteners on the inside of the retaining ring that fit into the seat on the steering wheel hub. In working position, the steering wheel presses on the ring to release it from its fasteners and thus allow both plates to turn freely. When the steering wheel is removed, the spring-loaded ring locks rotation between both plates. This function prevents the upper plate, now no longer secured to the steering wheel, from turning freely and unwinding or winding the coil inside the device and possibly causing it to break.The following must be observed during operations that require removal of the steering wheel and device.- always work with the car's wheels aligned straight ahead.
- lock the cable, for safety reasons, using a band before removing it from the steering column switch unit.
| If the upper plate should turn in relation to the lower plate for any reason |
| ... DATA ERROR - CROPPED TEXT | Ошибка данных - Текст обрезан ... |
|---|