312000314 - 1072B10 INLET MANIFOLD - R + R AND REPLACE SEAL

Removing ( Refitting )     Op. 5530B10 BATTERY - R+R     Op. 5530B52 BATTERY SUPPORT/DRIP TRAY - R.R     Op. 1048A10 AIR FILTER ASSEMBLY - R.R.     Op. 1048A23 COLD AIR INTAKE FOR AIR FILTER - R.R     Op. 1048B44 RIGID AIR SUPPLY PIPE BETWEEN HEAT EXCHANGER AND INTAKE MANIFOLD - R.R.     Op. 1080D28 OIL VAPOUR RECOVERY PIPE BETWEEN SEPARATOR AND TURBO - R.R.     Op. 1080D34 ENGINE OIL VAPOUR SEPARATOR - R + R     Op. 1080C82 E.G.R. - VALVE HEAT EXCHANGER ASSEMBLY - CONNECTOR PIPES - R.R.     Op. 7210E22 R.R. WINDSCREEN BASE TRIM 1. Undo nut (1a) and disconnect engine compartment junction unit power cable (1b).

	Description	Component
1b	ENGINE COMPARTMENT JUNCTION UNIT	See B001 JUNCTION UNIT

1. Detach the fuel pressure sensor electrical connection.

	Description	Component
1	FUEL PRESSURE SENSOR	See K083 FUEL PRESSURE SENSOR

1. Disconnect the electrical connection for the fuel pressure regulator.

	Description	Component
1	FUEL PRESSURE REGULATOR	See N077 FUEL PRESSURE REGULATOR

1. Disconnect the electrical connection for the turbocharging sensor.

	Description	Component
1	TURBOCHARGING SENSOR	See K082 SUPERCHARGING SENSOR

- Release the engine electrical wiring from the retaining bands housed on the intake manifold. 1. Undo retaining bolts (1a) and remove intake manifold (1b) from its housing. Refitting ( Removing ) 1. Fit intake manifold (1a) in place and tighten retaining bolts (1b) to the recommended torque.

Component	Fastening	dia	Value (daNm)	Validity
Intake manifold (on cylinder head)	Bolt	M8x1.25x65	2.5	1.3 Multijet

Component	Fastening	dia	Value (daNm)	Validity
Intake manifold (on cylinder head)	Bolt	M8x1.25x20	2.5	1.3 Multijet

1. Connect the electrical connection for the turbocharging sensor.

	Description	Component
1	TURBOCHARGING SENSOR	See K082 SUPERCHARGING SENSOR

1. Connect the electrical connection for the fuel pressure regulator.

	Description	Component
1	FUEL PRESSURE REGULATOR	See N077 FUEL PRESSURE REGULATOR

1. Connect the electrical connection for the fuel pressure sensor.

	Description	Component
1	FUEL PRESSURE SENSOR	See K083 FUEL PRESSURE SENSOR

1. Connect power cable (1a) to the engine compartment junction unit and tighten nut (1b). - Attach the engine electrical wiring to the retaining bands housed on the intake manifold.     Op. 7210E22 R.R. WINDSCREEN BASE TRIM     Op. 1080C82 E.G.R. - VALVE HEAT EXCHANGER ASSEMBLY - CONNECTOR PIPES - R.R.     Op. 1080D34 ENGINE OIL VAPOUR SEPARATOR - R + R     Op. 1080D28 OIL VAPOUR RECOVERY PIPE BETWEEN SEPARATOR AND TURBO - R.R.     Op. 1048B44 RIGID AIR SUPPLY PIPE BETWEEN HEAT EXCHANGER AND INTAKE MANIFOLD - R.R.     Op. 1048A23 COLD AIR INTAKE FOR AIR FILTER - R.R     Op. 1048A10 AIR FILTER ASSEMBLY - R.R.     Op. 5530B52 BATTERY SUPPORT/DRIP TRAY - R.R     Op. 5530B10 BATTERY - R+R