323002129 - 5580C86 SIDE BAG CABLE LOOM (ONE) LH OR RH - R.R OR REPLACE

Removing ( Refitting )
FOLLOW ALL THE RECOMMENDED SAFETY INSTRUCTIONS    Op. 5580C AIR BAG SYSTEM
    Op. 7045A10 FRONT SEAT (ONE), LEFT OR RIGHT - R.R.     Op. 7045A44 FRONT SEAT INTERIOR GUARD (ONE), LEFT OR RIGHT - R.R     Op. 7045A24 FRONT SEAT BACKREST ANGLE ADJUSTMENT KNOB (ONE), LEFT OR RIGHT - R.R.     Op. 7045A56 DRIVER'S SEAT HEIGHT ADJUSTMENT DEVICE CONTROL LEVER - R.R     Op. 7045A43 FRONT SEAT EXTERIOR GUARD (ONE), LEFT OR RIGHT - R.R     Op. 5580C44 FRONT SIDE BAG MODULE (ONE) LH OR RH - R.R 1. Working in the side Air Bag module housing, cut the wiring retaining band.2. Refit the wiring (2a) inside the opening (2b).
1. Disconnect the electrical connections (1a), (1b), working at the rear of the backrest.2. Disconnect the retainer for the electrical connection from the lumbar band.3. Cut the band retaining the wiring to the lumbar band.4. Release the wiring retainer.5. Extract the backrest wiring branch (5a) from the opening (5b).
1. Detach the electrical connection.2. Disconnect the edge (2a) of the cushion cover from the retainers (2b).3. Disconnect the wiring retainers from the springs.4. Keep the wiring.
1. If necessary, remove the connector holder (1a) from the individual connectors (1b), (1c), (1d) working as described later on.2. If inserted, extract the locking slide.3. Using a screwdriver, move the fastening levers (3a) sideways, in the direction of the arrows.
1. Extract the individul connectors (1a) from the connector holder (1b).
Refitting ( Removing ) - Observe the following precautions.
- Check that the wiring is intact and there are no signs of damage.- If new wiring is being fitted, position the labels as described below.- Remove the detachable part of the adhesive label from the new wiring. Place a copy of the label in a special folder containing the vehicle details (model, registration date, chassis number) and the serial number of the old backrest cover. The file should be kept for future checks.- Fit the detachable part of the original label on the lower part of the seat, where similar labels for the seat,Side Bag module and backrest cover can already be found.
If the connector holder has been removed, refit the individual connectors and place the levers in a central position.- Position the wiring.- Connect the wiring retainers to the springs.- Connect the edge of the cushion cover to the retainers.- Secure the electrical connection for the cushion heater pad.- Insert the backrest wiring branch via the opening.- Attach the wiring retainer.- Fit the wiring retaining band.- Connect the electrical connection to the retainer.- Connect the electrical connections for the backrest heater pad and lumbar adjustment motor.- Pass the wiring inside the opening.- Working in the Side Bag module housing, fit the wiring retaining band.    Op. 5580C44 FRONT SIDE BAG MODULE (ONE) LH OR RH - R.R     Op. 7045A43 FRONT SEAT EXTERIOR GUARD (ONE), LEFT OR RIGHT - R.R     Op. 7045A56 DRIVER'S SEAT HEIGHT ADJUSTMENT DEVICE CONTROL LEVER - R.R     Op. 7045A24 FRONT SEAT BACKREST ANGLE ADJUSTMENT KNOB (ONE), LEFT OR RIGHT - R.R.     Op. 7045A44 FRONT SEAT INTERIOR GUARD (ONE), LEFT OR RIGHT - R.R     Op. 7045A10 FRONT SEAT (ONE), LEFT OR RIGHT - R.R. - After refitting the seat, use an Examiner to check that the system has not acquired errors during the operation.