3330B02 PEDAL ASSEMBLY - R.R - Fiat - LINEA - eLearn

323001090 - 3330B02 PEDAL ASSEMBLY - R.R

) Op. 5530B10 BATTERY - R+R Op. 5530B52 BATTERY SUPPORT/DRIP TRAY - R.R - Undo the plug for the brake/clutch fluid reservoir and drain it referring to Op. 0010T67 HYDRAULIC CLUTCH SYSTEM - BLEED AIR - Disconnect the clutch pump supply pipe from the brake-clutch fluid reservoir.1.3 Multijet - 1.4 16v TJet versions1. Lift up the clip (1a) and disconnect the vibration damper (1b) from the clutch pump (1c).

1.4 8v version1. Lift up the clip (1a) and disconnect pipe (1b) from clutch pump (1c).

- Disconnect the electrical connection for the accelerator pedal.

	Description	Connector
-	ACCELERATOR PEDAL POTENTIOMETER	See K055 ACCELERATOR PEDAL POTENTIOMETER

- Disconnect the electrical connection for the brake pedal switch.

	Description	Connector
-	BRAKE PEDAL SWITCH	See I030 BRAKE PEDAL SWITCH

- Disconnect the electrical connection for the clutch pedal switch.

	Description	Connector
-	CLUTCH PEDAL SWITCH	See I031 CLUTCH PEDAL SWITCH

1. Using the special tool, press the retaining tabs (1a) securing the brake servo push rod (1b) to the brake pedal (1c).

Tool	Description	Function	Validity
2000010500	Calliper	Disconnect the master cylinder from the clutch pedal

1. Remove the retaining device (1a), then release the brake servo push rod (1b) from the brake pedal (1c) and keep the brake servo push rod spherical head housing cover (1d).

Always replace the retaining device (1a) for the brake servo push rod each time it is removed, even if it appears to be undamaged.

1. Undo the bolt (1a) and disconnect the steering column (1b) from the steering box pinion.

1. Undo the nuts securing the pedal mounting to the brake servo and to the bodyshell.2. Remove the pedal assembly complete with mounting and clutch pump.

Refitting ( Removing

) - Place the pedal assembly in position and secure it to the brake servo and to the bodyshell tightening the nuts to the recommended torque.

Component	Fastening	dia	Value (daNm)	Validity
Pedal unit mounting	Nut	M8	1.7 ÷ 2.6

Component	Fastening	dia	Value (daNm)	Validity
Brake servo	Nut	M8	1.7 ÷ 2.6

1. Fit the new retaining device (1a) on the brake pedal (1b) so that the fastening clips (1c) are secured; position the brake servo push rod spherical head housing cover (1d).

Always replace the retaining device (1a) for the brake servo push rod each time it is removed, even if it appears to be undamaged.

- Retract the brake servo slightly, lift up the brake pedal and position the brake servo push rod by the retaining device.- Press the brake pedal to fit the brake servo push rod on the retaining device.- Connect the steering column to the steering box pinion tightening the bolt to the recommended torque.

Component	Fastening	dia	Value (daNm)	Validity
Steering column to steering box pinion	Bolt	M10	5.0 ÷ 6.0

- Connect the electrical connection for the clutch pedal switch.

	Description	Connector
-	CLUTCH PEDAL SWITCH	See I031 CLUTCH PEDAL SWITCH

- Connect the electrical connection for the brake pedal switch.

	Description	Connector
-	BRAKE PEDAL SWITCH	See I030 BRAKE PEDAL SWITCH

- Connect the electrical connection for the accelerator pedal switch.

	Description	Connector
-	ACCELERATOR PEDAL POTENTIOMETER	See K055 ACCELERATOR PEDAL POTENTIOMETER

- Connect the clutch pump supply pipe to the brake-clutch fluid reservoir.1.4 8v version- Connect the pipe to the clutch pump and secure it using the clip.1.3 Multijet - 1.4 16v TJet versions- Connect the vibration damper to the clutch pump and secure it using the clip. Op. 5530B52 BATTERY SUPPORT/DRIP TRAY - R.R Op. 5530B10 BATTERY - R+R Op. 0010T67 HYDRAULIC CLUTCH SYSTEM - BLEED AIR Op. 3330B16 PEDAL UNIT ASSEMBLY - DISMANTLING AND REASSEMBLY AT THE BENCH