4130A10 POWER STEERING BOX - R+R - Fiat - LINEA - eLearn

323002538 - 4130A10 POWER STEERING BOX - R+R

) - Position the vehicle on a lift. Op. 7055B54 UNDER ENGINE PROTECTION/GUARD - R.R. Op. 7055B66 ENGINE COMPARTMENT DUST COVER IN RIGHT FRONT WHEEL ARCH - R.R. Op. 4450B12 FRONT WHEELS (TWO) - R+R Op. 1008C32 GEARBOX LOWER REACTION ROD -R.R. - Remove the power steering fluid reservoir cap and remove the fluid using a syringe. 1. Undo the steering column fixing bolt (1a) and disconnect the joint (1b) for the power steering box.

1. Undo the connectors (1a), disconnect the pipes (1b) from the power steering box and release them from the retaining clips.

- Release the retaining clip for the gear selection and engagement rods from the front suspension crossmember.1. Undo the nut fixing the steering link to the front steering knuckle.2. Fit the tool and disconnect the steering rod from the steering knuckle.

Tool	Description	Function	Validity
1871000700	Extractor	Extracting steering rod from strut

3. Disconnect the rod for the power steering box from the steering knuckle. Carry out the same operation and disconnect the other rod.

- Without disconnecting the track control arms and the anti-roll bar, support the front suspension crossmember, undo the securing bolts on the bodyshell and the strut, undo the bolts fixing the power steering box and lower the front suspension crossmember until there is enough space to remove the power steering box.Refer to the procedure: Op. 4410D15 FRONT SUSPENSION CROSSMEMBER COMPLETE WITH TRACK CONTROL ARMS AND ANTI-ROLL BAR - R.R- Move the power steering box and extract it from its housing.

Refitting ( Removing

) - Place the power steering box and the front suspension crossmember in position. Tighten the bolts fixing the power steering box and the bolts fixing the front suspension crossmember to the bodyshell and to the strut.Refer to the procedure: Op. 4410D15 FRONT SUSPENSION CROSSMEMBER COMPLETE WITH TRACK CONTROL ARMS AND ANTI-ROLL BAR - R.R- Connect the power steering box rod to the steering knuckle and tighten the nut (to be replaced) to the specified torque.

Component	Fastening	dia	Value (daNm)	Validity
Steering rod to pillar	Nut	M10	3.6 ÷ 4.4

- Carry out the same operation and connect the other rod.- Secure the retaining clip for the gear selection and engagement rods to the front suspension crossmember.- Connect the pipes to the power steering box and tighten the connectors to the specified torque.

Component	Fastening	dia	Value (daNm)	Validity
Filler on power steering pump	-	M16	3.6 ÷ 4.4	1.4 8v1.3 Multijet

- Secure the power steering pipes to the retaining clips.- Connect the coupling for the power steering box and tighten the steering column fixing bolt to the recommended torque.

Component	Fastening	dia	Value (daNm)	Validity
Steering column to steering box pinion	Bolt	M10	5.0 ÷ 6.0

Op. 1008C32 GEARBOX LOWER REACTION ROD -R.R. Op. 4450B12 FRONT WHEELS (TWO) - R+R Op. 7055B66 ENGINE COMPARTMENT DUST COVER IN RIGHT FRONT WHEEL ARCH - R.R. Op. 7055B54 UNDER ENGINE PROTECTION/GUARD - R.R. Op. 0010T71 POWER STEERING FLUID CHECK LEVEL AND TOP UP IF NECESSARY Op. 4450A10 FRONT WHEEL GEOMETRY - CHECK USING OPTICAL EQUIPMENT - INCLUDES ADJUSTMENT IF NECESSARY - Remove the vehicle from the lift.