1032D12 TIMING SYSTEM PROTECTIVE COVER(S) - R.R. - Lancia - THESIS - eLearn

74889 - 1032D12 Timing system protective COVER(S) - R.R.

) - Position the vehicle on a lift.- Open the boot, remove the cover on the left hand side and disconnect the negative battery lead.- Position a suitable container for collecting the engine coolant.- Raise the lift.1. Disconnect the lower radiator pipe.

See in Op. 7040D50 ENGINE COMPARTMENT UPPER SOUND INSULATION SHIELD - R.R. See in Op. 4450B04 Right FRONT WHEEL (one) - R.R.- Raise the vehicle on the lift. See in Op. 7055B54 PROTECTION/GUARD under engine - R.R. See in Op. 7055B42 FRONT WHEEL ARCH LINER (one), left or right - R.R. See in Op. 7055B64 Engine compartment DUST SEAL in front wheel arch (one), left or right - R.R. See in Op. 1048A21 AIR INLET HOSE FROM INTAKE TO FILTER - R.R. See in Op. 1048A50 air inlet pipe to turbocharger - r + r See in Op. 1048A10 COMPLETE AIR FILTER -R.R. See in Op. 1016A40 Ignition COIL COVER on cylinder head - R.R.1. Disconnect the coolant pipe retaining band on the cylinder head.2. Undo the nut fixing the expansion tank (this nut also fastens the windscreen washer fluid reservoir).3. Disconnect the electrical connection for the engine coolant level.

	Description	Connector
3	Engine coolant level sensor	K026

4. Disconnect the pipe (4a) and raise the expansion tank (4b) and remove it.

1. Undo the bolt (1a), loosen the bolt (1b) and rotate the reaction rod connecting rod.

- Raise the vehicle on the lift.1. Undo the nuts fixing the catalytic converter to the centre section of the exhaust pipe.2. Remove the mounting bracket for the front section of the exhaust pipe.

- Lower the vehicle on the lift, then position a hydraulic lift under the bellhousing.1. Undo the bolts fixing the engine support to the gearbox.- Gradually lower the hydraulic lift and rest the gearbox on the front crossmember.

See in Op. 1092G10 Engine components single drive BELT - R.R. See in Op. 1092A10 Crankshaft PULLEY - R.R. for versions with air conditioner1. Undo the bolt fixing the auxiliary shaft drive belt idle pulley.2. Undo the five bolts (2a) and remove the timing drive belt protective cover (2b).

Refitting ( Removing

) - Position the timing drive belt cover and secure it using the fixing bolts.

	Value - daNm	Fastening	Component	Ø
.	0.9	Bolt	TIMING BELT PROTECTIVE COVER(S)	M6

- Tighten the bolt fixing the auxiliary shaft drive belt idle pulley. See in Op. 1092A10 Crankshaft PULLEY - R.R. for versions with air conditioner See in Op. 1092G10 Engine components single drive BELT - R.R.- Position a hydraulic lift under the gearbox bellhousing.- Screw in and tighten the bolt fixing the engine support to the gearbox to the recommended torque.

	Value - daNm	Fastening	Component	Ø
.	5	Bolt	POWER UNIT GEAR BOX END RIGID MOUNT	M10 X 1.25

- Raise the vehicle on the lift.- Tighten the nuts fixing the catalytic converter to the centre section of the exhaust pipe.

	Value - daNm	Fastening	Component	Ø
.	(to cable centre section) 2.8	Nut	CATALYTIC CONVERTER (ONE)	M8

- Fit the mounting bracket for the front section of the exhaust pipe.

	Value - daNm	Fastening	Component	Ø
.	(on engine oil sump) 4	Nut	CATALYTIC CONVERTER MOUNT	M10 X 1.25

	Value - daNm	Fastening	Component	Ø
.	(to catalytic converter) 2.8	Bolt	CATALYTIC CONVERTER MOUNT	M8

- Lower the vehicle on the lift.- Connect the connecting rod to the reaction rod and secure it using the bolts.

	Value - daNm	Fastening	Component	Ø
.	(to bracket on bodyshell) 5	Bolt	POWER UNIT REACTION ROD	M10 X 1.25

	Value - daNm	Fastening	Component	Ø
.	(to engine support) 5	Bolt	POWER UNIT REACTION ROD	M10 X 1.25

- Position the expansion tank and secure it using the nut.- Connect the pipes and the electrical connection for the engine coolant level.

	Description	Connector
.	Engine coolant level sensor	K026

See in Op. 1016A40 Ignition COIL COVER on cylinder head - R.R. See in Op. 1048A10 COMPLETE AIR FILTER -R.R. See in Op. 1048A50 air inlet pipe to turbocharger - r + r See in Op. 1048A21 AIR INLET HOSE FROM INTAKE TO FILTER - R.R. See in Op. 1016A40 Ignition COIL COVER on cylinder head - R.R. See in Op. 7055B64 Engine compartment DUST SEAL in front wheel arch (one), left or right - R.R. See in Op. 7055B42 FRONT WHEEL ARCH LINER (one), left or right - R.R.- Connect the lower radiator pipe.- Lower the vehicle on the lift. See in Op. 4450B04 Right FRONT WHEEL (one) - R.R.- Connect the negative battery lead. See in Op. 0010T20 Engine REFRIGERANT FLUID - Change See in Op. 7055B54 PROTECTION/GUARD under engine - R.R. See in Op. 7040D50 ENGINE COMPARTMENT UPPER SOUND INSULATION SHIELD - R.R.- Remove the vehicle from the lift.