177989 - 4420D10 REAR SUSPENSION AXLE - R.R.

Removing ( Refitting ) - Position the vehicle on a lift.    See in Op. 7040D50 ENGINE COMPARTMENT UPPER SOUND INSULATION SHIELD - R.R.    See in Op. 7040B10 LOAD CARRYING COMPARTMENT LINING - R.R.    See in Op. 7040B17 Luggage compartment/load platform side trim flap (one) - Replace    See in Op. 7040B13 Luggage compartment/load platform SIDE LINING - R.R.    See in Op. 4450B11 Rear WHEEL (one) - R.R.    See in Op. 7055B43 REAR WHEEL ARCH LINER (one), left or right - R.R.    See in Op. 4440K31 LEFT OR RIGHT REAR INTELLIGENT SUSPENSION SHOCK ABSORBER (ONE) - R.R.-
Using the EXAMINER diagnostic equipment carry out the procedure for moving the rear brake pads away from the discs.
1. Undo the bolts fixing the brake back plate to the hub.2. Undo the fixing bolt (2a) and remove the ABS sensor (2b).
- Raise the vehicle.     See in Op. 1076B20 Rear exhaust SILENCER - R.R.-    See in Op. 1076A40 Exhaust pipe HEAT SHIELDS - R.R.- 1. Disconnect the electrical connection for the headlamp alignment rear potentiometer.
DescriptionConnector
1 Headlamp alignment corrector rear potentiometer (CAF)K002
1. Position the tool for supporting the rear suspension axle.
DescriptionCodeFunction
1 Support1.860.975.001Rear axle (support)
2. Undo the bolts fixing the rear axle to the bodyshell.3. Remove the rear axle, complete with springs, anti-roll bar and track control arms.
Refitting ( Removing ) - Fit the rear axle, complete with springs, anti-roll bar and track control arms.- Tighten the bolts fixing the rear axle to the bodyshell.- Remove the tool positioned previously for supporting the rear suspension axle.
DescriptionCodeFunction
.Support1.860.975.001Rear axle (support)
DescriptionConnector
.Headlamp alignment corrector rear potentiometer (CAF)K002
    See in Op. 1076B20 Rear exhaust SILENCER - R.R.-    See in Op. 1076A40 Exhaust pipe HEAT SHIELDS - R.R.- - Lower the vehicle.- Fit the ABS sensor in the special housing in the rear brakes.- Fit the brake caliper bracket complete with caliper and tighten the fixing bolts.
Using the EXAMINER diagnostic equipment carry out the procedure for calibrating the rear brakes.
    See in Op. 4440K31 LEFT OR RIGHT REAR INTELLIGENT SUSPENSION SHOCK ABSORBER (ONE) - R.R.-    See in Op. 7055B43 REAR WHEEL ARCH LINER (one), left or right - R.R.    See in Op. 4450B11 Rear WHEEL (one) - R.R.    See in Op. 7040B13 Luggage compartment/load platform SIDE LINING - R.R.    See in Op. 7040B17 Luggage compartment/load platform side trim flap (one) - Replace    See in Op. 7040B10 LOAD CARRYING COMPARTMENT LINING - R.R.- Place the vehicle in Standard "A" conditions, in other words with the vehicle mass complete, spare wheel, tool kit, all supplies and accessories (oil, engine coolant, etc.) and a full fuel tank.- Check that the tyre inflation pressure is correct.- Position the vehicle on a support so that the wheels are resting on the ground. - Check that after the vehicle has been placed in standard "A" conditions, the measurement "D"-"C" corresponds to the figure given in the table below.
SubjectValue
.Rear wheel geometrymm
-D - C21 ± 5
-Standard A-
- Tighten the bolts fixing the rear axle to the bodyshell to torque.
Value - daNmFasteningComponentØ  
.2.5BoltREAR RIGID AXLEM8
Value - daNmFasteningComponentØ  
.10BoltREAR RIGID AXLEM12x1.5
    See in Op. 4450A40 REAR WHEEL GEOMETRY - Check using optical equipment - Includes rear wheel toe-in adjustment if necessary    See in Op. 7040D50 ENGINE COMPARTMENT UPPER SOUND INSULATION SHIELD - R.R.