78888 - 4420B34 Rear suspension TRACK CONTROL ARM, left or right - R.R.

Removing ( Refitting ) - Position the vehicle on a lift.- Disconnect the negative battery terminal.    See in Op. 7040D50 ENGINE COMPARTMENT UPPER SOUND INSULATION SHIELD - R.R.    See in Op. 7040B10 LOAD CARRYING COMPARTMENT LINING - R.R.    See in Op. 7040B17 Luggage compartment/load platform side trim flap (one) - Replace    See in Op. 7040B13 Luggage compartment/load platform SIDE LINING - R.R.    See in Op. 4450B11 Rear WHEEL (one) - R.R.    See in Op. 7055B43 REAR WHEEL ARCH LINER (one), left or right - R.R.    See in Op. 4440K30 LEFT OR RIGHT REAR INTELLIGENT SUSPENSION SHOCK ABSORBER (ONE) - R.R.-    See in Op. 3310B36 REAR BRAKE CALIPER (one), left or right - R.R.    See in Op. 3310B48 REAR BRAKE DISC (one), left or right - R.R.    See in Op. 4450D10 Rear wheel HUB, left or right - R.R. with wheel removed-    See in Op. 3310B59 Rear brake DISC GUARD (one), left or right- R.R.    See in Op. 4450D15 Rear wheel hub STUB AXLE, left or right - R.R. Including replacement of bush, if necessary-1. Undo the bolts fixing the track control arm to the rear axle.2. Remove the rear suspension track control arm.- If the track control arm is being replaced, remove the connecting rod from the track control arm and fit it on the new track control arm.
Refitting ( Removing ) - Position the rear suspension track control arm.- Tighten the bolts fixing the track control arm to the rear axle.- Proceed with refitting the remaining components to ensure the optimum conditions to be able to rest the vehicle on the support.    See in Op. 4450D15 Rear wheel hub STUB AXLE, left or right - R.R. Including replacement of bush, if necessary-    See in Op. 3310B59 Rear brake DISC GUARD (one), left or right- R.R.    See in Op. 4450D10 Rear wheel HUB, left or right - R.R. with wheel removed-    See in Op. 3310B48 REAR BRAKE DISC (one), left or right - R.R.    See in Op. 3310B36 REAR BRAKE CALIPER (one), left or right - R.R.    See in Op. 4440K30 LEFT OR RIGHT REAR INTELLIGENT SUSPENSION SHOCK ABSORBER (ONE) - R.R.-    See in Op. 4450B11 Rear WHEEL (one) - R.R.- Place the vehicle in Standard "A" conditions, in other words with the vehicle mass complete, spare wheel, tool kit, all supplies and accessories (oil, engine coolant, etc.) and a full fuel tank.- Check that the tyre inflation pressure is correct.- Position the vehicle on a support so that the wheels are resting on the ground. - Check that after the vehicle has been placed in standard "A" conditions, the measurement "D"-"C" corresponds to the figure given in the table below.
SubjectValue
.Rear wheel geometrymm
-D - C21 ± 5
-Standard A-
Value - daNmFasteningComponentØ  
.(Crossmember side) 10BoltREAR WISHBONEM12X1.25
    See in Op. 4450A40 REAR WHEEL GEOMETRY - Check using optical equipment - Includes rear wheel toe-in adjustment if necessary    See in Op. 7055B43 REAR WHEEL ARCH LINER (one), left or right - R.R.    See in Op. 7040B13 Luggage compartment/load platform SIDE LINING - R.R.    See in Op. 7040B17 Luggage compartment/load platform side trim flap (one) - Replace    See in Op. 7040B10 LOAD CARRYING COMPARTMENT LINING - R.R.    See in Op. 7040D50 ENGINE COMPARTMENT UPPER SOUND INSULATION SHIELD - R.R.- Connect the negative battery terminal.- Remove the vehicle from the lift.