93639 - 1056B51 CAM ANGLE SENSOR - R.R.

Removing ( Refitting ) - Position the vehicle on a lift.- Open the boot, remove the cover on the left hand side and disconnect the negative battery lead.    See in Op. 7040D50 ENGINE COMPARTMENT UPPER SOUND INSULATION SHIELD - R.R.    See in Op. 4450B04 Right FRONT WHEEL (one) - R.R.- Raise the vehicle on the lift.    See in Op. 7055B54 PROTECTION/GUARD under engine - R.R.    See in Op. 7055B42 FRONT WHEEL ARCH LINER (one), left or right - R.R.    See in Op. 7055B64 Engine compartment DUST SEAL in front wheel arch (one), left or right - R.R.     See in Op. 1048A21 AIR INLET HOSE FROM INTAKE TO FILTER - R.R.    See in Op. 1048A50 air inlet pipe to turbocharger - r + r    See in Op. 1048A10 COMPLETE AIR FILTER -R.R.     See in Op. 1016A40 Ignition COIL COVER on cylinder head - R.R.    See in Op. 1092G10 Engine components single drive BELT - R.R.    See in Op. 1092A10 Crankshaft PULLEY - R.R. for versions with air conditioner    See in Op. 1032D12 Timing system protective COVER(S) - R.R.    See in Op. 1032B10 TOOTHED timing BELT - R.R. for timing adjustment or replacement1. Undo the bolt (1a) for the exhaust side timing driven pulley using the tools (1b) and (1c) for counter-torque.
DescriptionCodeFunction
1b Support for counter-torque1.860.831.000Loosen/tighten driven toothed pulley bolt
DescriptionCodeFunction
1c Spanner for rotating timing pullies1.860.831.002Loosen/tighten camshaft drive pulley bolt
2. Remove the exhaust side timing driven pulley.3. Undo the inlet side timing driven pulley bolts (3a) using the tool (3b) for counter-torque.
DescriptionCodeFunction
3b Counter-torque1.860.856.000Loosen/tighten inlet side camshaft drive pulley bolts
4. Remove the inlet side timing driven pulley.
1. Disconnect the electrical connection for the cam angle sensor.
DescriptionConnector
1 Timing sensorK047
2. Undo the bolts (2a) and remove the guard (2b).3. Undo the bolts (3a) and remove the cam angle sensor (3b).
Refitting ( Removing ) - Position the cam angle sensor and secure it using the bolts.
Value - daNmFasteningComponentØ  
.0.9BoltCAM ANGLE SENSOR CAMSHAFTM6
- Position the cam angle sensor wiring and fit the guard.- Connect the electrical connection for the cam angle sensor.
DescriptionConnector
.Timing sensorK047
- Position the inlet side timing driven pulley and secure it without tightening the bolts.- Position the exhaust side timing driven pulley and secure it without tightening the bolt.
The bolts securing the pullies are tightened when refitting the timing drive belt.
    See in Op. 1032B10 TOOTHED timing BELT - R.R. for timing adjustment or replacement    See in Op. 1032D12 Timing system protective COVER(S) - R.R.    See in Op. 1092A10 Crankshaft PULLEY - R.R. for versions with air conditioner    See in Op. 1092G10 Engine components single drive BELT - R.R.    See in Op. 1016A40 Ignition COIL COVER on cylinder head - R.R.     See in Op. 1048A10 COMPLETE AIR FILTER -R.R.    See in Op. 1048A50 air inlet pipe to turbocharger - r + r    See in Op. 1048A21 AIR INLET HOSE FROM INTAKE TO FILTER - R.R.     See in Op. 7055B64 Engine compartment DUST SEAL in front wheel arch (one), left or right - R.R.    See in Op. 7055B42 FRONT WHEEL ARCH LINER (one), left or right - R.R.- Lower the vehicle on the lift.    See in Op. 4450B04 Right FRONT WHEEL (one) - R.R.- Connect the negative battery lead.    See in Op. 0010T20 Engine REFRIGERANT FLUID - Change    See in Op. 7055B54 PROTECTION/GUARD under engine - R.R.    See in Op. 7040D50 ENGINE COMPARTMENT UPPER SOUND INSULATION SHIELD - R.R.- Remove the vehicle from the lift.