1060E40 PRESSURE PUMP SUPPORT - R.R. - Lancia - THESIS - eLearn

100661 - 1060E40 PRESSURE PUMP SUPPORT - R.R.

) - Position the vehicle on a lift.- Open the boot and disconnect the negative battery terminal. See in Op. 7040D50 ENGINE COMPARTMENT UPPER SOUND INSULATION SHIELD - R.R. See in Op. 1016A10 SOUND-PROOFING COVER - R.R. See in Op. 7055B54 PROTECTION/GUARD under engine - R.R. See in Op. 4450B04 Right FRONT WHEEL (one) - R.R. See in Op. 7055B42 FRONT WHEEL ARCH LINER (one), left or right - R.R. See in Op. 7055B64 Engine compartment DUST SEAL in front wheel arch (one), left or right - R.R. See in Op. 1092G10 Engine components single drive BELT - R.R. See in Op. 1032D12 Timing system protective COVER(S) - R.R. See in Op. 1032B10 TOOTHED timing BELT - R.R. for timing adjustment or replacement See in Op. 1060E30 PRESSURE PUMP drive PULLEY - R.R. See in Op. 1060F20 PIPE from PRESSURE PUMP to FUEL MANIFOLD - R.R. See in Op. 1060F34 PIPE from fuel MANIFOLD to INJEJCTOR - R.R. See in Op. 1060E10 PRESSURE PUMP for diesel injection - R.R.- Disconnect the negative battery terminal.1. Disconnect the electrical connection for the throttle casing pneumatic solenoid valve.

	Description	Connector
1	Throttle body solenoid valve	L062

2. Undo the fixing bolts (2a), disconnect the pipe (2b) connected to the pneumatic valve and remove the vacuum reservoir (2c).

1. Undo the two fixing bolts.2. Remove the vacuum reservoir support.

1. Undo the upper engine oil dipstick pipe fixing bolts.2. Undo the lower engine oil dipstick pipe fixing bolts.- Open the bands and release the electrical leads connected to it and release the timing sensor from the band.3. Remove the engine oil dipstick pipe.

1. Undo the fixing bolts.2. Remove the plastic protection fixed to the power assisted steering pump.

1. Undo the fixing bolts.2. Remove the pressure pump support.

Refitting ( Removing

) - Fit the pressure pump support tighten the fixing bolts to torque.

	Value - daNm	Fastening	Component	Ø
.	(Cylinder block/crankcase) 2.5	Bolt	INJECTION PRESSURE PUMP MOUNT	M8

	Value - daNm	Fastening	Component	Ø
.	(Intake manifold) 2.5	Bolt	INJECTION PRESSURE PUMP MOUNT	M8

- Fit the plastic protection for the power assisted steering pump.- Fit the engine oil dipstick pipe.- Tighten the bolts fixing the oil dipstick pipe.

	Value - daNm	Fastening	Component	Ø
.	0.9	Bolt	OIL LEVEL DIPSTICK PIPE	M6

- Fit the vacuum reservoir support in the housing in the pressure pump support.- Fit the vacuum reservoir in the support and tighten the fixing bolts.- Connect the connecting pipes to the pneumatic valve.- Connect the electrical connection for the solenoid valve.

	Description	Connector
.	Throttle body solenoid valve	L062

See in Op. 1060E10 PRESSURE PUMP for diesel injection - R.R. See in Op. 1060F34 PIPE from fuel MANIFOLD to INJEJCTOR - R.R. See in Op. 1060F20 PIPE from PRESSURE PUMP to FUEL MANIFOLD - R.R. See in Op. 1060E30 PRESSURE PUMP drive PULLEY - R.R. See in Op. 1032B10 TOOTHED timing BELT - R.R. for timing adjustment or replacement See in Op. 1032D12 Timing system protective COVER(S) - R.R. See in Op. 1092G10 Engine components single drive BELT - R.R. See in Op. 7055B64 Engine compartment DUST SEAL in front wheel arch (one), left or right - R.R. See in Op. 7055B42 FRONT WHEEL ARCH LINER (one), left or right - R.R. See in Op. 4450B04 Right FRONT WHEEL (one) - R.R. See in Op. 7055B54 PROTECTION/GUARD under engine - R.R. See in Op. 7040D50 ENGINE COMPARTMENT UPPER SOUND INSULATION SHIELD - R.R. See in Op. 1016A10 SOUND-PROOFING COVER - R.R.- Open the boot and connect the negative battery terminal.- Remove the vehicle from the lift.