1008A44 RIGID REAR POWER UNIT MOUNTING - R.R. - Lancia - THESIS - eLearn

75460 - 1008A44 RIGID REAR power unit MOUNTING - R.R.

) - Position the vehicle on a lift.- Open the boot and disconnect the negative battery terminal. See in Op. 7040D50 ENGINE COMPARTMENT UPPER SOUND INSULATION SHIELD - R.R. See in Op. 7055B54 PROTECTION/GUARD under engine - R.R. See in Op. 4450B04 Right FRONT WHEEL (one) - R.R. See in Op. 7055B42 FRONT WHEEL ARCH LINER (one), left or right - R.R. See in Op. 7055B42 FRONT WHEEL ARCH LINER (one), left or right - R.R. See in Op. 7055B64 Engine compartment DUST SEAL in front wheel arch (one), left or right - R.R. See in Op. 2710A31 INTERMEDIATE DRIVE SHAFT - R.R. See in Op. 1092G10 Engine components single drive BELT - R.R.1. Undo the bolts fixing the alternator.2. Disconnect the alternator electrical wiring.3. Remove the alternator.

	Description	Connector
2	Alternator	A010A

	Description	Connector
2	Alternator	A010B

- Lower the lift.1. Remove the alternator rear mounting bracket.

- Position the hydraulic engine support under the oil sump in order to work safely.1. Disconnect the electrical connection for the engine oil pressure sensor.

	Description	Connector
1	Insufficient engine oil pressure sensor	K030

2. Undo the nut fixing the support to the flexible mounting.3. Undo the bolt fixing the support to the oil sump.- Keep the spacers which are between the bolt and the sump.4. Undo the bolts fixing the support to the cylinder block/crankcase.5. Remove the intermediate driveshaft support which supports the engine.

Refitting ( Removing

) - Position the engine support which also supports the intermediate driveshaft in the special housing.- Tighten the bolts fixing the support to the engine support to the cylinder block/crankcase to torque.

	Value - daNm	Fastening	Component	Ø
.	5	Bolt	RIGID REAR SUPPORT POWER UNIT	M10 X 1.25

- Tighten the bolt fixing the support to the oil sump to torque.

	Value - daNm	Fastening	Component	Ø
.	2.5	Bolt	RIGID REAR SUPPORT POWER UNIT	M8

- Tighten the nut fixing the engine support to the flexible mounting on the chassis to torque.

	Value - daNm	Fastening	Component	Ø
.	5	Nut	RIGID REAR SUPPORT POWER UNIT	M10 X 1.25

- Connect the electrical connection for the engine oil pressure sensor.- Fit the alternator mounting bracket tightening the bolts fixing it to the cylinder block/crankcase to torque.

	Value - daNm	Fastening	Component	Ø
.	5	Bolt	FRONT ALTERNATOR SUPPORT	M10

- Fit the alternator assembly and tighten the bolts fixing it to the mounting.

	Value - daNm	Fastening	Component	Ø
.	5	Nut	ALTERNATOR ASSEMBLY	M10 X 1.25

	Value - daNm	Fastening	Component	Ø
.	7	Nut	ALTERNATOR ASSEMBLY	M12 X 1.25

- Connect the alternator electrical wiring.

	Description	Connector
.	Alternator	A010A

	Description	Connector
.	Alternator	A010B

See in Op. 1092G10 Engine components single drive BELT - R.R. See in Op. 2710A31 INTERMEDIATE DRIVE SHAFT - R.R. See in Op. 7055B64 Engine compartment DUST SEAL in front wheel arch (one), left or right - R.R. See in Op. 7055B42 FRONT WHEEL ARCH LINER (one), left or right - R.R. See in Op. 4450B04 Right FRONT WHEEL (one) - R.R. See in Op. 7055B54 PROTECTION/GUARD under engine - R.R.- [7055B04] See in Op. 7040D50 ENGINE COMPARTMENT UPPER SOUND INSULATION SHIELD - R.R.- Connect the battery terminal.