75463 - 1008A46 Power unit RIGID MOUNT - TIMING side - R&R

Refitting

    See in Op. 7055B54 PROTECTION/GUARD under engine - R.R.    See in Op. 4450B04 Right FRONT WHEEL (one) - R.R.- link 4450B04 missing    See in Op. 7055B42 FRONT WHEEL ARCH LINER (one), left or right - R.R.    See in Op. 7055B42 FRONT WHEEL ARCH LINER (one), left or right - R.R.    See in Op. 7055B64 Engine compartment DUST SEAL in front wheel arch (one), left or right - R.R.    See in Op. 1092G10 Engine components single drive BELT - R.R.    See in Op. 1016A10 SOUND-PROOFING COVER - R.R.    See in Op. 5040A10 Air conditioning coolant circuit - Drying and Repressurizing    See in Op. 5040A10 Air conditioning coolant circuit - Drying and Repressurizing    See in Op. 5040A20 Air conditioning COMPRESSOR - R.R. - Includes fluid level check and top up if necessary1. Undo the fixing bolt.2. Remove the auxiliary shaft drive belt fixed tensioner

1. Undo the nut (1a) fixing the rigid rear support (1b) to the mounting.

- Position a hydraulic lift under the bellhousing in order to work safely.- Raise the power unit and temporarily secure the rigid support to the gearbox bellhousing.- Move the hydraulic lifting device under the engine oil sump.1. Undo the nut fixing the compressor/engine support to the flexible mounting.2. Undo the bolts fixing the support to the cylinder block/crankcase.- Using the hydraulic lift, slightly raise the engine until the support slips away from the flexible mounting stud.3. Remove the compressor/engine support.

Refitting ( Removing ) - Fit the compressor/engine support.- Tighten the bolts fixing the engine/compressor support to the cylinder block/crankcase to the recommended torque.

	Value - daNm	Fastening	Component	Ø
.	(cylinder block/crankcase side) 7	Nuts	RIGID ENGINE MOUNT, TIMING SIDE	M10X1.25

- Tighten the nut fixing the engine support to the flexible mounting.

	Value - daNm	Fastening	Component	Ø
.	5	Nut	RIGID TIMING SUPPORT POWER UNIT	M10X1.25

- Remove the hydraulic lift under the engine.- Tighten the nut fixing the engine support/intermediate shaft to the flexible mounting.

	Value - daNm	Fastening	Component	Ø
.	5	Nut	RIGID REAR SUPPORT POWER UNIT	M10 X 1.25

- Fit the auxiliary shaft drive belt fixed tensioner

	Value - daNm	Fastening	Component	Ø
.	5	Bolt	SINGLE BELT FIXED TENSIONER VARIOUS	M12X1.25

    See in Op. 5040A20 Air conditioning COMPRESSOR - R.R. - Includes fluid level check and top up if necessary    See in Op. 1092G10 Engine components single drive BELT - R.R.    See in Op. 1016A10 SOUND-PROOFING COVER - R.R.    See in Op. 7055B64 Engine compartment DUST SEAL in front wheel arch (one), left or right - R.R.    See in Op. 7055B42 FRONT WHEEL ARCH LINER (one), left or right - R.R.    See in Op. 4450B04 Right FRONT WHEEL (one) - R.R.- link 4450B04 missing    See in Op. 7055B54 PROTECTION/GUARD under engine - R.R.    See in Op. 5040A10 Air conditioning coolant circuit - Drying and Repressurizing    See in Op. 7040D50 ENGINE COMPARTMENT UPPER SOUND INSULATION SHIELD - R.R.- Connect the battery terminal.- Remove the vehicle from the lift.