79350 - 5505B10 FRONT DOOR built in wiring (one), left or right - R.R. with water protection or support frame removed

Removing ( Refitting ) 1. Disconnect the electrical connectors (1a), (1b), (1c), (1d).
DescriptionConnector
1a Left front electric window motorN060
DescriptionConnector
1a Right front electric window motorN061
DescriptionConnector
1b Right front door lock geared motorN051A
DescriptionConnector
1c Switch on driver's exterior handleI022
DescriptionConnector
1c Switch on passenger side exterior handleI023
DescriptionConnector
1d Left external rear view mirrorP060
DescriptionConnector
1d Right external rear view mirrorP061
DescriptionConnector
1e Speaker in left front doorP035
DescriptionConnector
1e Speaker in right front doorP036
DescriptionConnector
1b Left front door lock geared motorN050A
DescriptionConnector
1b Left front door lock geared motorN050B
DescriptionConnector
1b Right front door lock geared motorN051B
2. Lift up the protective tab (2a) and disconnect the electrical connector (2b).
DescriptionConnector
2b Left front door couplingD030
DescriptionConnector
2b Right front door couplingD031
3. Release the electrical wiring from the retaining springs and remove it from the housing.
DescriptionConnector
1b RF aerial on left front door for passive entry (NPE)P094
DescriptionConnector
1b RF aerial on right front door for passive entry (NPE)P095
DescriptionConnector
1c Unit signalling driver's front door locking/unlockingE036
DescriptionConnector
1c Unit signalling passenger front door locking/unlockingE037
1. Disconnect the electrical connectors (1a), (1b) and (1c) and keep the passive entry aerial (1d), the front door locking/unlocking signal unit (1e) and the front door locking/unlocking switch (1f).
DescriptionConnector
1a Driver's front door locking/unlocking switchI026
DescriptionConnector
1a Passenger front door locking/unlocking switchI027
Refitting ( Removing ) - Check that the wiring is not damaged and that the individual conducts are correctly fastened to the connections.- If necessary, carry out continuity tests.1. Keep the passive entry aerial (1a), the front door locking/unlocking signal unit (1b) and the front door locking/unlocking switch (1c) and connect the connectors (1d), (1e) and (1f).
DescriptionConnector
1d Driver's front door locking/unlocking switchI026
DescriptionConnector
1d Passenger front door locking/unlocking switchI027
DescriptionConnector
1e RF aerial on left front door for passive entry (NPE)P094
DescriptionConnector
1e RF aerial on right front door for passive entry (NPE)P095
DescriptionConnector
1f Unit signalling driver's front door locking/unlockingE036
DescriptionConnector
1f Unit signalling passenger front door locking/unlockingE037
1. Connect the electrical connectors (1a), (1b), (1c), (1d).
DescriptionConnector
1a Left front electric window motorN060
DescriptionConnector
1a Right front electric window motorN061
DescriptionConnector
1b Left front door lock geared motorN050A
DescriptionConnector
1c Switch on driver's exterior handleI022
DescriptionConnector
1c Switch on passenger side exterior handleI023
DescriptionConnector
1d Left external rear view mirrorP060
DescriptionConnector
1d Right external rear view mirrorP061
DescriptionConnector
1e Speaker in left front doorP035
DescriptionConnector
1e Speaker in right front doorP036
DescriptionConnector
1b Right front door lock geared motorN051B
DescriptionConnector
1b Left front door lock geared motorN050B
DescriptionConnector
1b Right front door lock geared motorN051A
2. Lower the protective tab (2a) and connect the electrical connector (2b).
DescriptionConnector
2b Left front door couplingD030
DescriptionConnector
2b Right front door couplingD031
3. Secure the electrical wiring to the retaining springs and remove it from the housing.
- Check that all the devices connected to the front door wiring are working properly.