849857 - 1008A44 RIGID REAR power unit MOUNTING - R.R.

Removing ( Refitting ) - Position the vehicle on a lift.- Open the boot and disconnect the negative battery terminal.    See in Op. 7055B54 PROTECTION/GUARD under engine - R.R.    See in Op. 4450B04 Right FRONT WHEEL (one) - R.R.    See in Op. 7055B42 FRONT WHEEL ARCH LINER (one), left or right - R.R.    See in Op. 7055B64 Engine compartment DUST SEAL in front wheel arch (one), left or right - R.R.    See in Op. 2710A31 INTERMEDIATE DRIVE SHAFT - R.R.- Lower the vehicle.    See in Op. 1016A10 SOUND-PROOFING COVER - R.R.    See in Op. 7040D50 ENGINE COMPARTMENT UPPER SOUND INSULATION SHIELD - R.R.    See in Op. 1048B44 RIGID air supply PIPE from heat exchanger to intake manifold - R.R.    See in Op. 1048A56 UPPER RESONATOR - R.R.    See in Op. 1092G10 Engine components single drive BELT - R.R.    See in Op. 1092A10 Crankshaft PULLEY - R.R.    See in Op. 1092G15 Engine components single belt MOVING TENSIONER - R.R. with belt removed1. Undo the bolts fixing the alternator.- Disconnect the alternator electrical wiring.2. Remove the alternator.
DescriptionConnector
.AlternatorA010A
DescriptionConnector
.AlternatorA010B
- Lower the lift.1. Remove the alternator rear mounting bracket.
- Position the hydraulic engine support under the oil sump in order to work safely.1. Disconnect the electrical connection for the insufficient engine oil pressure sensor.
DescriptionConnector
1 Insufficient engine oil pressure sensorK030
2. Undo the nut fixing the support to the flexible mounting.3. Undo the bolt fixing the support to the oil sump.- Keep the spacers which are between the bolt and the sump.4. Undo the bolts fixing the support to the cylinder block/crankcase.5. Remove the intermediate driveshaft support which supports the engine.
Refitting ( Removing ) - Position the engine support which also supports the intermediate driveshaft in the special housing.- Tighten the bolts fixing the support to the engine support to the cylinder block/crankcase to torque.
Value - daNmFasteningComponentØ  
.5BoltRIGID REAR SUPPORT POWER UNITM10 X 1.25
- Tighten the bolt fixing the support to the oil sump to torque.
Value - daNmFasteningComponentØ  
.2.5BoltRIGID REAR SUPPORT POWER UNITM8
- Tighten the nut fixing the engine support to the flexible mounting on the chassis to torque.
Value - daNmFasteningComponentØ  
.4,5NutPOWER UNIT REAR RIGID MOUNTM10 X 1.25
- Connect the electrical connection for the insufficient engine oil pressure sensor.
DescriptionConnector
.Insufficient engine oil pressure sensorK030
- Fit the alternator mounting bracket tightening the bolts fixing it to the cylinder block/crankcase to torque.
Value - daNmFasteningComponentØ  
.5BoltFRONT ALTERNATOR SUPPORTM10
- Fit the alternator assembly and tighten the bolts fixing it to the mounting.
Value - daNmFasteningComponentØ  
.5NutALTERNATOR ASSEMBLYM10 X 1.25
Value - daNmFasteningComponentØ  
.7NutALTERNATOR ASSEMBLYM12 X 1.25
- Connect the alternator electrical wiring.
DescriptionConnector
.AlternatorA010A
DescriptionConnector
.AlternatorA010B
    See in Op. 1092G15 Engine components single belt MOVING TENSIONER - R.R. with belt removed    See in Op. 1092A10 Crankshaft PULLEY - R.R.    See in Op. 1092G10 Engine components single drive BELT - R.R.    See in Op. 1048A56 UPPER RESONATOR - R.R.    See in Op. 1048B44 RIGID air supply PIPE from heat exchanger to intake manifold - R.R.    See in Op. 7040D50 ENGINE COMPARTMENT UPPER SOUND INSULATION SHIELD - R.R.    See in Op. 1016A10 SOUND-PROOFING COVER - R.R.    See in Op. 2710A31 INTERMEDIATE DRIVE SHAFT - R.R.    See in Op. 7055B64 Engine compartment DUST SEAL in front wheel arch (one), left or right - R.R.    See in Op. 7055B42 FRONT WHEEL ARCH LINER (one), left or right - R.R.    See in Op. 4450B04 Right FRONT WHEEL (one) - R.R.    See in Op. 7055B54 PROTECTION/GUARD under engine - R.R.- Connect the battery terminal.- Remove the vehicle from the lift.