4450D15 REAR WHEEL HUB STUB AXLE, LEFT OR RIGHT - R.R. INCLUDING REPLACEMENT OF BUSH, IF NECESSARY - Lancia - THESIS - eLearn

180293 - 4450D15 Rear wheel hub STUB AXLE, left or right - R.R. Including replacement of bush, if necessary

) - Position the vehicle on a lift. See in Op. 4450B11 Rear WHEEL (one) - R.R. See in Op. 7055B44 Left rear wheel arch liner - R.R. See in Op. 3310B36 REAR BRAKE CALIPER (one), left or right - R.R. See in Op. 3310B48 REAR BRAKE DISC (one), left or right - R.R. See in Op. 4440K30 LEFT OR RIGHT REAR INTELLIGENT SUSPENSION SHOCK ABSORBER (ONE) - R.R. See in Op. 4450D10 Rear wheel HUB, left or right - R.R. with wheel removed See in Op. 3310B59 Rear brake DISC GUARD (one), left or right- R.R. See in Op. 4450D10 Rear wheel HUB, left or right - R.R. with wheel removed1. Fit the tool for compressing the spring.

	Description	Code	Function
1	Extractor - fitting tool	1.870.829.000	Compress and decompress the rear suspension coil springs at the bench

2. Position a hydraulic device under the track control arm for safety reasons.3. Undo the nut fixing the vertical rod to the stub axle.4. Undo the bolts fixing the camber and toe in rods to the stub axle.5. Undo the bolt fixing the stub axle to the track control arm.6. Remove the wheel hub stub axle.

Refitting ( Removing

) - Fit the wheel hub stub axle.- Tighten the bolt fixing the stub axle to the track control arm.- Tighten the bolt fixing toe in rod to the stub axle.- Tighten the bolt fixing the rod to the stub axle.- Tighten the nut fixing the connecting rod to the stub axle.- Remove the hydraulic device placed under the track control arm.- Remove the tool for compressing the spring.

	Description	Code	Function
1	Extractor - fitting tool	1.870.829.000	Compress and decompress the rear suspension coil springs at the bench

See in Op. 4450D10 Rear wheel HUB, left or right - R.R. with wheel removed See in Op. 3310B59 Rear brake DISC GUARD (one), left or right- R.R. See in Op. 4450D10 Rear wheel HUB, left or right - R.R. with wheel removed See in Op. 4440K30 LEFT OR RIGHT REAR INTELLIGENT SUSPENSION SHOCK ABSORBER (ONE) - R.R. See in Op. 3310B48 REAR BRAKE DISC (one), left or right - R.R. See in Op. 3310B36 REAR BRAKE CALIPER (one), left or right - R.R. See in Op. 7055B44 Left rear wheel arch liner - R.R. See in Op. 4450B11 Rear WHEEL (one) - R.R.- Place the vehicle in Standard "A" conditions, in other words with the vehicle mass complete, spare wheel, tool kit, all supplies and accessories (oil, engine coolant, etc.) and a full fuel tank.- Check that the tyre inflation pressure is correct.- Position the vehicle on a support so that the wheels are resting on the ground - Check that after the vehicle has been placed in standard "A" conditions, the measurement "D"-"C" corresponds to the figure given in the table below.

	Subject	Value
.	Rear wheel geometry	mm
-	D - C	21 ± 5
-	Standard A	-

- Tighten the bolt fixing the stub axle to the track control arm.

	Value - daNm	Fastening	Component	Ø
.	11	Bolt	STEERING KNUCKLE/REAR STUB AXLES	M12

- Tighten the bolt fixing the toe in rod to the stub axle to torque.

	Value - daNm	Fastening	Component	Ø
.	10	Bolt	TOE IN RODS	M12

- Tighten the bolts fixing the rod to the steering knuckle to torque.

	Value - daNm	Fastening	Component	Ø
.	(Steering knuckle) 11	Bolt	HOUSING LINK	M12X1.25

- Tighten the nut fixing the connecting rod to the steering knuckle.

	Value - daNm	Fastening	Component	Ø
.	(Steering knuckle) 12	Nut	VERTICAL CONNECTING ROD	M12X1.25

See in Op. 4450A40 REAR WHEEL GEOMETRY - Check using optical equipment - Includes rear wheel toe-in adjustment if necessary