850071 - 1028H10 CONNECTING ROD and PISTON SET - R&R

Refitting

    See in Op. 7040D50 ENGINE COMPARTMENT UPPER SOUND INSULATION SHIELD - R.R.    See in Op. 1016A10 SOUND-PROOFING COVER - R.R.    See in Op. 1048B44 RIGID air supply PIPE from heat exchanger to intake manifold - R.R.    See in Op. 1048A56 UPPER RESONATOR - R.R.    See in Op. 1048A50 air inlet pipe to turbocharger - r + r    See in Op. 1048A21 AIR INLET HOSE FROM INTAKE TO FILTER - R.R.    See in Op. 1048A10 COMPLETE AIR FILTER -R.R.    See in Op. 1064A24 TURBOCHARGER - EXHAUST MANIFOLD - HOSE CONNECTED TO EXHAUST PIPE - R.R.    See in Op. 4450B04 Right FRONT WHEEL (one) - R.R.    See in Op. 7055B42 FRONT WHEEL ARCH LINER (one), left or right - R.R.    See in Op. 7055B64 Engine compartment DUST SEAL in front wheel arch (one), left or right - R.R.    See in Op. 1092G10 Engine components single drive BELT - R.R.    See in Op. 1092G21 Engine components single belt FIXED TENSIONER - R.R. with belt removed    See in Op. 1092A10 Crankshaft PULLEY - R.R.    See in Op. 1032D12 Timing system protective COVER(S) - R.R.    See in Op. 1016C10 SINGLE CYLINDER HEAD - R.R. and Replace gasket    See in Op. 1020A20 CRANKCASE SUMP - R.R. clean contact surfaces and apply sealant1. Undo the bolts (1a) and remove the connecting rod caps (1b) complete with half-bearings (1c).

1. Release and remove the piston/connecting rod assemblies (1a) complete with half-bearings (1b).

Refitting ( Removing ) 1. Place the piston/connecting rod assemblies (1a) in their housings complete with half-bearings (1b) using a suitable fitting tool (1c).

The piston-connecting rod assemblies should be fitted in the cylinder block/crankcase so that the drain on the piston skirt is aligned with the oil jet on the engine block.

- Place the caps complete with half-bearings in their housings and secure them tightening the bolts to the recommended torque.

Fit the connecting rods so that the number stamped on each rod faces towardt he same side as the number stamped on the big end (inlet side).

	Value - daNm	Fastening	Component	Ø
.	2.0 + 60°	Bolt	CONNECTING ROD CAPS	M9

- Use the tool for the angular tightening of the connecting rod cap bolts.

	Description	Code	Function
.	Torque wrench	1.860.942.000	Connecting rod cap bolt tightening

    See in Op. 1020A20 CRANKCASE SUMP - R.R. clean contact surfaces and apply sealant    See in Op. 1016C10 SINGLE CYLINDER HEAD - R.R. and Replace gasket    See in Op. 1032D12 Timing system protective COVER(S) - R.R.    See in Op. 1092A10 Crankshaft PULLEY - R.R.    See in Op. 1092G21 Engine components single belt FIXED TENSIONER - R.R. with belt removed    See in Op. 1092G10 Engine components single drive BELT - R.R.    See in Op. 7055B64 Engine compartment DUST SEAL in front wheel arch (one), left or right - R.R.    See in Op. 7055B42 FRONT WHEEL ARCH LINER (one), left or right - R.R.    See in Op. 4450B04 Right FRONT WHEEL (one) - R.R.    See in Op. 1064A24 TURBOCHARGER - EXHAUST MANIFOLD - HOSE CONNECTED TO EXHAUST PIPE - R.R.    See in Op. 1048A10 COMPLETE AIR FILTER -R.R.    See in Op. 1048A21 AIR INLET HOSE FROM INTAKE TO FILTER - R.R.    See in Op. 1048A50 air inlet pipe to turbocharger - r + r    See in Op. 1048A56 UPPER RESONATOR - R.R.    See in Op. 1048B44 RIGID air supply PIPE from heat exchanger to intake manifold - R.R.    See in Op. 1016A10 SOUND-PROOFING COVER - R.R.    See in Op. 7040D50 ENGINE COMPARTMENT UPPER SOUND INSULATION SHIELD - R.R.    See in Op. 7055B54 PROTECTION/GUARD under engine - R.R.- Fill the engine cooling system as described in the operation:    See in Op. 0010T20 Engine REFRIGERANT FLUID - Change- Top up or, if necessary, change the engine oil referring to the instructions in the description:    See in Op. 0010T10 ENGINE OIL - Change- Or:    See in Op. 0010T11 ENGINE OIL - Check level and top up if necessary- Remove the vehicle from the lift.