74889 - 1032D12 Timing system protective COVER(S) - R.R.

Refitting

- Raise the vehicle on the lift.    See in Op. 7055B54 PROTECTION/GUARD under engine - R.R.    See in Op. 7055B64 Engine compartment DUST SEAL in front wheel arch (one), left or right - R.R.    See in Op. 7055B42 FRONT WHEEL ARCH LINER (one), left or right - R.R.    See in Op. 1092G10 Engine components single drive BELT - R.R.- Lower the lift.    See in Op. 7040D50 ENGINE COMPARTMENT UPPER SOUND INSULATION SHIELD - R.R.    See in Op. 1088B10 Engine coolant SUPPLY RESERVOIR - R.R.    See in Op. 1048A21 AIR INLET HOSE FROM INTAKE TO FILTER - R.R.    See in Op. 1048A28 vacuum air circuit resonator pipe - r+r    See in Op. 1008C10 Power unit REACTION ROD - Replace    See in Op. 1016A42 LEFT CYLINDER HEAD IGNITION COIL COVER - R.R.    See in Op. 1048A11 COMPLETE AIR FILTER -R.R.1. Release the retainers (1a) and disconnect the gearbox bowden cable (1b).

1. Disconnect the main gearbox wiring connectors.

	Description	Connector
1	Automatic transmission solenoid valves	L050A

	Description	Connector
1	Automatic transmission solenoid valves	L050B

	Description	Connector
1	Automatic transmission solenoid valves	L050C

1. Open the protective flap (1a) and undo the nut (1b) fixing the starter motor supply lead (1c) to the junction node and move the lead between the junction node and the motor aside.

	Description	Connector
1b	Contact board	A005A

	Description	Connector
1b	Contact board	A005B

1. Position a hydraulic jack under the gearbox casing and undo the two nuts (1a) fixing the gearbox side engine support (1b) to the bracket (1c), then lower the jack until the gearbox casing is resting on the suspension frame.

1. Open the band (1a) retaining the power assisted steering pipes (1b) and move them aside.2. Undo the six upper bolts (2a) fixing the timing belt upper cover (2b) and remove it.

Refitting ( Removing ) - Position the timing belt upper cover and tighten the fixing bolts.

	Value - daNm	Fastening	Component	Ø
.	0.9	Bolt	TIMING BELT PROTECTIVE COVER(S)	M6

- Position the power assisted steering pipes and close the retaining band.- Raise the jack positioned under the gearbox casing and tighten the two nuts fixing the gearbox side engine support to the bracket to the recommended torque.

	Value - daNm	Fastening	Component	Ø
.	5	Nut	POWER UNIT GEAR BOX END RIGID MOUNT	M10 X 1.25

- Connect the lead between the junction node and the starter motor to the actual node and tighten the fixing nut, then close the protective flap.

	Value - daNm	Fastening	Component	Ø
.	0.5	Nut	TERMINAL/MOTOR LEAD	M8

- Connect the main gearbox wiring connectors.

	Description	Connector
.	Automatic transmission solenoid valves	L050A

	Description	Connector
.	Automatic transmission solenoid valves	L050B

	Description	Connector
.	Automatic transmission solenoid valves	L050C

- Position the gearbox bowden cable and secure the retainers.    See in Op. 1048A11 COMPLETE AIR FILTER -R.R.    See in Op. 1016A42 LEFT CYLINDER HEAD IGNITION COIL COVER - R.R.    See in Op. 1008C10 Power unit REACTION ROD - Replace    See in Op. 1048A28 vacuum air circuit resonator pipe - r+r    See in Op. 1048A21 AIR INLET HOSE FROM INTAKE TO FILTER - R.R.    See in Op. 1088B10 Engine coolant SUPPLY RESERVOIR - R.R.    See in Op. 7040D50 ENGINE COMPARTMENT UPPER SOUND INSULATION SHIELD - R.R.- Raise the vehicle.    See in Op. 1092G10 Engine components single drive BELT - R.R.    See in Op. 7055B64 Engine compartment DUST SEAL in front wheel arch (one), left or right - R.R.    See in Op. 4450B04 Right FRONT WHEEL (one) - R.R.- Raise the vehicle on the lift.- Connect the negative battery lead, then close the boot.- Remove the vehicle from the lift.    See in Op. 0010T21 ENGINE COOLANT - Check density and top up if necessary-