109484 - 2130B40 Gear selector SOLENOID VALVE UNIT - R.R.

Removing ( Refitting ) - Position the vehicle on a lift.
Before proceed with the operation of removing the solenoid unit, position the gear lever in "N"
- Open the boot, remove the cover on the left hand side and disconnect the negative battery lead.    See in Op. 7040D50 ENGINE COMPARTMENT UPPER SOUND INSULATION SHIELD - R.R.    See in Op. 1048A21 AIR INLET HOSE FROM INTAKE TO FILTER - R.R.    See in Op. 1048A28 vacuum air circuit resonator pipe - r+r    See in Op. 1016A42 LEFT CYLINDER HEAD IGNITION COIL COVER - R.R.    See in Op. 1048A11 COMPLETE AIR FILTER -R.R.- Raise the vehicle on the lift.    See in Op. 7055B54 PROTECTION/GUARD under engine - R.R.- Position a container to collect the automatic transmission fluid.1. Undo the plug and drain the transmission fluid
1. Undo the lower bolts (1a) fixing the solenoid valve unit cover (1b).
- Lower the vehicle1. Release the air conditioning system pipe (1b) from the retaining spring (1a)2. Undo the upper bolts (2a) fixing the solenoid valve unit cover (2b) and remove it taking care not to damage the gasket (2c) underneath.
1. Disconnect the eight connectors (1a) for the solenoid valves.
1. Undo the bolt (1a) fixing the retaining bracket and remove the oil temperature sensor (1b).
proceed carefully in order not to damage the electrical connection
1. Undo the two bolts (1a) fixing the inlet cover (1b) and remove it together with the gasket.
1. Undo the bolts fixing the solenoid valve unit starting with the top ones (1a) and then, after having raised the vehicle, finish with the bottom ones (1b).
1. Disconnect the gear selector lever (1a) and remove the solenoid valve unit (1b) releasing it from underneath.
1. Remove the two gaskets underneath the solenoid valve unit
Refitting ( Removing ) - Clean the work area thoroughly- Place a new set of gaskets underneath the solenoid valve unit1. Position the solenoid valve unit simultaneously engaging the valve control lever (1a) and the gear engagement control (1b) and secure the unit using a bolt.
1. Position the remaining bolts (1a), (1b) and (1c) as illustrated in the diagram and tighten them to the recommended torque.
Value - daNmFasteningComponentØ  
1a 1BoltSOLENOID UNITM6 X 55
Value - daNmFasteningComponentØ  
1b 1BoltSOLENOID UNITM6 X 50
Value - daNmFasteningComponentØ  
1c 1BoltSOLENOID UNITM6 X 16
1. Position the inlet cover (1a) with a new gasket (1b) and tighten the two fixing bolts (1c) to the recommended torque.
Value - daNmFasteningComponentØ  
1c 1BoltSOLENOID UNITM6 X 50
1. Position the temperature sensor (1a) and secure it using the retaining bracket (1b) tightening the fixing bolt (1c) to the recommended torque.
Value - daNmFasteningComponentØ  
1c 1BoltSOLENOID UNITM6 X 55
- Connect the eight solenoid valve connectors.- Apply a suitable sealant to the cover matching surface.1. Tighten the nine bolts fixing the solenoid valve unit cover to the recommended torque.
Value - daNmFasteningComponentØ  
1a 1.3BoltSOLENOID VALVE COVER FIXING, BOLTM8 X 15
- Secure the air conditioning system pipe to the retaining spring on the engine support frame.- Position the gearbox oil plug    See in Op. 7055B54 PROTECTION/GUARD under engine - R.R.- Lower the vehicle    See in Op. 0010T44 AUTOMATIC TRANSMISSION FLUID - Change    See in Op. 1048A11 COMPLETE AIR FILTER -R.R.    See in Op. 1016A42 LEFT CYLINDER HEAD IGNITION COIL COVER - R.R.    See in Op. 1048A28 vacuum air circuit resonator pipe - r+r    See in Op. 1048A21 AIR INLET HOSE FROM INTAKE TO FILTER - R.R.    See in Op. 7040D50 ENGINE COMPARTMENT UPPER SOUND INSULATION SHIELD - R.R.- Connect the negative battery lead, then close the boot.- Remove the vehicle from the lift.