4420D10 REAR SUSPENSION AXLE - R.R. - Lancia - THESIS - eLearn

177989 - 4420D10 REAR SUSPENSION AXLE - R.R.

) - Position the vehicle on a lift. See in Op. 7040D50 ENGINE COMPARTMENT UPPER SOUND INSULATION SHIELD - R.R. See in Op. 7040B10 LOAD CARRYING COMPARTMENT LINING - R.R. See in Op. 7040B17 Luggage compartment/load platform side trim flap (one) - Replace See in Op. 7040B13 Luggage compartment/load platform SIDE LINING - R.R. See in Op. 4450B11 Rear WHEEL (one) - R.R. See in Op. 7055B43 REAR WHEEL ARCH LINER (one), left or right - R.R. See in Op. 4440K31 LEFT OR RIGHT REAR INTELLIGENT SUSPENSION SHOCK ABSORBER (ONE) - R.R.-

Using the EXAMINER diagnostic equipment carry out the procedure for moving the rear brake pads away from the discs.

1. Undo the bolts fixing the brake back plate to the hub.2. Undo the fixing bolt (2a) and remove the ABS sensor (2b).

- Raise the vehicle. See in Op. 1076B20 Rear exhaust SILENCER - R.R. See in Op. 1076A40 Exhaust pipe HEAT SHIELDS - R.R. 1. Disconnect the electrical connection for the headlamp alignment rear potentiometer.

	Description	Connector
1	Headlamp alignment corrector rear potentiometer (CAF)	K002

1. Position the tool for supporting the rear suspension axle.

	Description	Code	Function
1	Support	1.860.975.001	Rear axle (support)

2. Undo the bolts fixing the rear axle to the bodyshell.3. Remove the rear axle, complete with springs, anti-roll bar and track control arms.

Refitting ( Removing

) - Fit the rear axle, complete with springs, anti-roll bar and track control arms.- Tighten the bolts fixing the rear axle to the bodyshell.- Remove the tool positioned previously for supporting the rear suspension axle.

	Description	Code	Function
.	Support	1.860.975.001	Rear axle (support)

	Description	Connector
.	Headlamp alignment corrector rear potentiometer (CAF)	K002

See in Op. 1076B20 Rear exhaust SILENCER - R.R. See in Op. 1076A40 Exhaust pipe HEAT SHIELDS - R.R. - Lower the vehicle.- Fit the ABS sensor in the special housing in the rear brakes.- Fit the brake caliper bracket complete with caliper and tighten the fixing bolts.

Using the EXAMINER diagnostic equipment carry out the procedure for calibrating the rear brakes.

See in Op. 4440K31 LEFT OR RIGHT REAR INTELLIGENT SUSPENSION SHOCK ABSORBER (ONE) - R.R.- See in Op. 7055B43 REAR WHEEL ARCH LINER (one), left or right - R.R. See in Op. 4450B11 Rear WHEEL (one) - R.R. See in Op. 7040B13 Luggage compartment/load platform SIDE LINING - R.R. See in Op. 7040B17 Luggage compartment/load platform side trim flap (one) - Replace See in Op. 7040B10 LOAD CARRYING COMPARTMENT LINING - R.R.- Place the vehicle in Standard "A" conditions, in other words with the vehicle mass complete, spare wheel, tool kit, all supplies and accessories (oil, engine coolant, etc.) and a full fuel tank.- Check that the tyre inflation pressure is correct.- Position the vehicle on a support so that the wheels are resting on the ground. - Check that after the vehicle has been placed in standard "A" conditions, the measurement "D"-"C" corresponds to the figure given in the table below.

	Subject	Value
.	Rear wheel geometry	mm
-	D - C	21 ± 5
-	Standard A	-

- Tighten the bolts fixing the rear axle to the bodyshell to torque.

	Value - daNm	Fastening	Component	Ø
.	2.5	Bolt	REAR RIGID AXLE	M8

	Value - daNm	Fastening	Component	Ø
.	10	Bolt	REAR RIGID AXLE	M12x1.5

See in Op. 4450A40 REAR WHEEL GEOMETRY - Check using optical equipment - Includes rear wheel toe-in adjustment if necessary See in Op. 7040D50 ENGINE COMPARTMENT UPPER SOUND INSULATION SHIELD - R.R.