193033 - 5530B36 LEAD between starter motor and alternator - R.R.

Refitting

    See in Op. 4450B04 Right FRONT WHEEL (one) - R.R.    See in Op. 7055B64 Engine compartment DUST SEAL in front wheel arch (one), left or right - R.R.    See in Op. 7055B54 PROTECTION/GUARD under engine - R.R.    See in Op. 1048A21 AIR INLET HOSE FROM INTAKE TO FILTER - R.R.    See in Op. 1048A28 vacuum air circuit resonator pipe - r+r    See in Op. 1008C10 Power unit REACTION ROD - Replace    See in Op. 1048A11 COMPLETE AIR FILTER -R.R.    See in Op. 1072B50 Air CHAMBER - R.R.    See in Op. 2710A31 INTERMEDIATE DRIVE SHAFT - R.R.    See in Op. 1084B30 CARTRIDGE ENGINE OIL FILTER -R.R.    See in Op. 1076B84 EXHAUST PIPE BETWEEN RIGHT PRECONVERTER AND CATALYTIC CONVERTER - R.R.    See in Op. 1080B39 RIGHT CATALYTIC PRECONVERTER - R.R. or Replace Gasket1. Undo the nut (1a) fastening the end (1b) of the starter motor supply lead.

	Description	Connector
1b	Starter motor	A020A

	Description	Connector
1b	Starter motor	A020B

- After having loosened the alternator fastenings, proceed as described below1. Undo the bolt (1a) fastening the coolant connectors (1b) to the alternator (1c).2. Open the band (2a) securing the pipe (2b) between the crankcase and the engine oil heat exchanger (2c).3. Undo the middle heat exchanger nut and remove the heat exchanger.

1. Undo the nut (1a) fastening the end of the supply lead (1b) between the starter motor and the alternator and remove it.

	Description	Connector
1b	Starter motor	A020A

	Description	Connector
1b	Starter motor	A020B

Refitting ( Removing ) 1. Tighten the nut (1a) fastening the end of the supply lead (1b) between the starter motor and the alternator to the recommended torque.

	Value - daNm	Fastening	Component	Ø
.	0.9	Nut	ALTERNATOR	M8

	Description	Connector
1b	Starter motor	A020A

1. Position the heat exchanger (1a) and secure the connectors (1b) complete with seals to the alternator using the bolt (1c).

Always replace the seals on the alternator cooling pipe connectors.

2. Close the retaining band (2a) for the pipe (2b) between the heat exchanger and the crankcase.3. Tighten the middle heat exchanger connector to the recommended torque.

	Value - daNm	Fastening	Component	Ø
.	3	Connector	ENGINE OIL HEAT EXCHANGER	M18 X 1,5

- Secure the starter motor end of the lead between the starter motor and the alternator using the nut.    See in Op. 1080B39 RIGHT CATALYTIC PRECONVERTER - R.R. or Replace Gasket    See in Op. 1076B84 EXHAUST PIPE BETWEEN RIGHT PRECONVERTER AND CATALYTIC CONVERTER - R.R.    See in Op. 1084B30 CARTRIDGE ENGINE OIL FILTER -R.R.    See in Op. 2710A31 INTERMEDIATE DRIVE SHAFT - R.R.    See in Op. 1072B50 Air CHAMBER - R.R.    See in Op. 1048A11 COMPLETE AIR FILTER -R.R.    See in Op. 1008C10 Power unit REACTION ROD - Replace    See in Op. 1048A28 vacuum air circuit resonator pipe - r+r    See in Op. 1048A21 AIR INLET HOSE FROM INTAKE TO FILTER - R.R.    See in Op. 7055B54 PROTECTION/GUARD under engine - R.R.    See in Op. 7055B64 Engine compartment DUST SEAL in front wheel arch (one), left or right - R.R.    See in Op. 4450B04 Right FRONT WHEEL (one) - R.R.    See in Op. 0010T11 ENGINE OIL - Check level and top up if necessary-    See in Op. 7040D50 ENGINE COMPARTMENT UPPER SOUND INSULATION SHIELD - R.R.- Connect the negative battery lead, then close the boot.- Remove the vehicle from the lift.