74604 - 1008A44 RIGID REAR power unit MOUNTING - R.R.

Refitting

    See in Op. 4450B04 Right FRONT WHEEL (one) - R.R.    See in Op. 7055B64 Engine compartment DUST SEAL in front wheel arch (one), left or right - R.R.    See in Op. 7055B54 PROTECTION/GUARD under engine - R.R.    See in Op. 7040D50 ENGINE COMPARTMENT UPPER SOUND INSULATION SHIELD - R.R.    See in Op. 1048A21 AIR INLET HOSE FROM INTAKE TO FILTER - R.R.    See in Op. 1048A28 vacuum air circuit resonator pipe - r+r    See in Op. 1008C10 Power unit REACTION ROD - Replace    See in Op. 1048A11 COMPLETE AIR FILTER -R.R.    See in Op. 1092G10 Engine components single drive BELT - R.R.    See in Op. 1072B50 Air CHAMBER - R.R.    See in Op. 2710A31 INTERMEDIATE DRIVE SHAFT - R.R.    See in Op. 1084B30 CARTRIDGE ENGINE OIL FILTER -R.R.    See in Op. 1076B84 EXHAUST PIPE BETWEEN RIGHT PRECONVERTER AND CATALYTIC CONVERTER - R.R.-    See in Op. 1080B39 RIGHT CATALYTIC PRECONVERTER - R.R. or Replace Gasket-    See in Op. 5530A10 ALTERNATOR - R.R.    See in Op. 1084C10 Engine oil heat exchanger - R.R.1. Undo the nut (1a) fixing the front engine support (1b) to the flexible mounting.

1. Position a hydraulic jack (1a) under the engine oil sump (1b).2. Undo the nuts (2a) and the Allen screws (2b) fixing the rigid support (2c) to the cylinder block/crankcase.3. Undo the centre nut (3a) fixing the support to the engine support frame (3b).

- Raise the jack, as necessary, and remove the support.1. Remove the plate located between the support and the cylinder block/crankcase.

Refitting ( Removing ) - Still working with the hydraulic engine support positioned under the engine oil sump, fit the plate, then position the rigid rear support.- Tighten the bolts and the nuts fixing the support to the cylinder block/crankcase to the recommended torque.

	Value - daNm	Fastening	Component	Ø
.	(to the cylinder block/crankcase) 2	Bolt	RIGID REAR SUPPORT POWER UNIT	M8

- Tighten the nut fixing the support to the flexible mounting to the recommended torque.

	Value - daNm	Fastening	Component	Ø
.	(to the cylinder block/crankcase) 2	Nut	RIGID REAR SUPPORT POWER UNIT	M8

- Tighten the nut fixing the support to the flexible mounting to the recommended torque.

	Value - daNm	Fastening	Component	Ø
.	(to the flexible mounting) 4	Nut	RIGID REAR SUPPORT POWER UNIT	M10

- Remove the hydraulic engine support1. Tighten the nut (1a) fixing the front engine support to the flexible mounting (1b) to the recommended torque.

	Value - daNm	Fastening	Component	Ø
1a	4,5	Nut	FRONT FLEXIBLE MOUNTING BLOCKS, POWER UNIT	M10X1.25

    See in Op. 1084C10 Engine oil heat exchanger - R.R.    See in Op. 5530A10 ALTERNATOR - R.R.    See in Op. 1080B39 RIGHT CATALYTIC PRECONVERTER - R.R. or Replace Gasket-    See in Op. 1076B84 EXHAUST PIPE BETWEEN RIGHT PRECONVERTER AND CATALYTIC CONVERTER - R.R.-    See in Op. 1084B30 CARTRIDGE ENGINE OIL FILTER -R.R.    See in Op. 2710A31 INTERMEDIATE DRIVE SHAFT - R.R.    See in Op. 1072B50 Air CHAMBER - R.R.    See in Op. 1092G10 Engine components single drive BELT - R.R.-    See in Op. 1048A11 COMPLETE AIR FILTER -R.R.    See in Op. 1008C10 Power unit REACTION ROD - Replace    See in Op. 1048A28 vacuum air circuit resonator pipe - r+r    See in Op. 1048A21 AIR INLET HOSE FROM INTAKE TO FILTER - R.R.    See in Op. 7040D50 ENGINE COMPARTMENT UPPER SOUND INSULATION SHIELD - R.R.    See in Op. 7055B54 PROTECTION/GUARD under engine - R.R.    See in Op. 7055B64 Engine compartment DUST SEAL in front wheel arch (one), left or right - R.R.    See in Op. 4450B04 Right FRONT WHEEL (one) - R.R.    See in Op. 7055B42 FRONT WHEEL ARCH LINER (one), left or right - R.R.- [0010T11]- Connect the negative battery lead, then close the boot.- Remove the vehicle from the lift.