1008A43 POWER UNIT RIGID MOUNT - AUTOMATIC GEARBOX SIDE - R&R - Lancia - THESIS - eLearn

183588 - 1008A43 Power unit RIGID MOUNT - AUTOMATIC GEARBOX side - R&R

) - Position the vehicle on a lift.- Open the boot, remove the cover on the left hand side and disconnect the negative battery lead. See in Op. 4450B02 Left FRONT WHEEL (one) - R.R. See in Op. 7055B42 FRONT WHEEL ARCH LINER (one), left or right - R.R. See in Op. 7040D50 ENGINE COMPARTMENT UPPER SOUND INSULATION SHIELD - R.R. See in Op. 1016A40 Ignition COIL COVER on cylinder head - R.R. See in Op. 1048A21 AIR INLET HOSE FROM INTAKE TO FILTER - R.R. See in Op. 1048A23 Cold AIR INTAKE for air filter - R.R. See in Op. 1048A28 vacuum air circuit resonator pipe - r+r See in Op. 1048A10 COMPLETE AIR FILTER -R.R. See in Op. 1048A48 HOSE BETWEEN RESONATOR AND THROTTLE CASING - R.R. See in Op. 7055B54 PROTECTION/GUARD under engine - R.R. See in Op. 1008C10 Power unit REACTION ROD - Replace1. Release the retainers (1a) and disconnect the gearbox bowden cable (1b).

1. Disconnect the main gearbox wiring connectors.

	Description	Connector
1	Automatic transmission solenoid valves	L050A

	Description	Connector
1	Automatic transmission solenoid valves	L050B

	Description	Connector
1	Automatic transmission solenoid valves	L050C

1. Open the protective flap (1a) and undo the nut (1b) fixing the starter motor supply lead (1c) to the junction node and move the lead between the junction node and the motor aside.

	Description	Connector
1c	Contact board	A005A

	Description	Connector
1c	Contact board	A005B

1. Position a hydraulic jack under the gearbox casing and undo the two nuts (1a) fixing the gearbox side engine support (1b) to the bracket (1c), then lower the jack until the gearbox casing is resting on the suspension frame.

1. Undo the nut (1a) fixing the flexible mounting (1b) to the rigid support (1c).2. Undo the upper bolt fixing the rigid support to the gearbox.

- Raise the vehicle1. Working via the wheel arch, undo the three side bolts fixing the rigid support to the gearbox.

- Remove the rigid support, complete with flexible mounting, from the engine compartment.- If necessary, replace the flexible mounting.

Refitting ( Removing

) 1. Proceed with reassembling the flexible mounting (1a) on the rigid support (1b) and then ensure that they are both correctly positioned in the vehicle in relation to the centering opening (1c) to allow the subsequent fastening of the support to the bodyshell.

- Working via the wheel arch, tighten the three side bolts fixing the rigid support to the gearbox to the recommended torque.

	Value - daNm	Fastening	Component	Ø
.	5	Bolt	POWER UNIT GEAR BOX END RIGID MOUNT	M10

- Lower the vehicle- Tighten the upper bolt fixing the rigid support to the gearbox to the recommended torque.

	Value - daNm	Fastening	Component	Ø
.	5	Bolt	POWER UNIT GEAR BOX END RIGID MOUNT	M10

- Tighten the nut fixing the rigid support to the flexible mounting to the recommended torque.

	Value - daNm	Fastening	Component	Ø
.	5	Nut	POWER UNIT GEAR BOX END RIGID MOUNT	M10 X 1.25

- Raise the jack positioned under the gearbox casing and tighten the two nuts fixing the gearbox side engine support to the bracket to the recommended torque.

	Value - daNm	Fastening	Component	Ø
.	5	Nut	POWER UNIT GEAR BOX END RIGID MOUNT	M10 X 1.25

- Connect the lead between the junction node and the starter motor to the actual node and tighten the fixing nut, then close the protective flap.

	Value - daNm	Fastening	Component	Ø
.	0.5	Nut	TERMINAL/MOTOR LEAD	M8

- Connect the main gearbox wiring connectors.

	Description	Connector
.	Automatic transmission solenoid valves	L050A

	Description	Connector
.	Automatic transmission solenoid valves	L050B

	Description	Connector
.	Automatic transmission solenoid valves	L050C

- Position the gearbox bowden cable and secure the fasteners. See in Op. 1008C10 Power unit REACTION ROD - Replace See in Op. 7055B54 PROTECTION/GUARD under engine - R.R. See in Op. 1048A48 HOSE BETWEEN RESONATOR AND THROTTLE CASING - R.R. See in Op. 1048A10 COMPLETE AIR FILTER -R.R. See in Op. 1048A28 vacuum air circuit resonator pipe - r+r See in Op. 1048A23 Cold AIR INTAKE for air filter - R.R. See in Op. 1048A21 AIR INLET HOSE FROM INTAKE TO FILTER - R.R. See in Op. 1016A40 Ignition COIL COVER on cylinder head - R.R. See in Op. 7040D50 ENGINE COMPARTMENT UPPER SOUND INSULATION SHIELD - R.R. See in Op. 7055B42 FRONT WHEEL ARCH LINER (one), left or right - R.R. See in Op. 4450B02 Left FRONT WHEEL (one) - R.R.- Connect the negative battery lead, then close the boot.- Remove the vehicle from the lift.