1028H14 SET OF PISTONS AND CONNECTING RODS - R.R. WITH ENGINE AND CYLINDER HEAD(S) REMOVED - Lancia - THESIS - eLearn

505837 - 1028H14 Set of pistons and connecting rods - R.R. with engine and cylinder head(s) removed

) 1. Undo the front and rear bolts (1b) fixing the crankcase sump using the spanner (1b).

	Description	Code	Function
1b	Spanner	1.860.834.000	Loosen/tighten front and rear crankcase sump bolts

2. Undo the side bolts (2a) fixing the crankcase sump using the spanner (2b).

	Description	Code	Function
2b	Spanner	1.860.833.000	Loosen/tighten crankcase sump side bolts

3. Cut the oil sump sealant using the tool.

	Description	Code	Function
3	Blade	1.870.718.000	Cut the crankcase sump sealant

4. Remove the crankcase sump.

1. Undo the bolts (1a) and remove the engine oil intake duct (1b) complete with gasket.

- Fit the tool for rotating the crankshaft and rotate it so that the connecting rod cap bolts are accessible.

	Description	Code	Function
.	Flange	1.860.815.000	Crankshaft rotation

1. Undo the bolts (1a) and remove the connecting rod caps (1b) and half-bearings (1c).2. Remove the piston- connecting rod assemblies (2a) complete with half-bearings (2b).

Refitting ( Removing

) - Place the piston-connecting rod assemblies, complete with half-bearings, in their housings.

Use a suitable tool for compressing the seals and then fitting in the cylinder liner/bore.

The pistons and connecting rods are fitted in the cylinder block/crankcase so that the large references (for the inlet valves) in the piston crown are facing the inlet side.

- Place the connecting rod caps complete with half bearings in their housings and secure them tightening the bolts to the recommended torque.

Fit the connecting rods so that the number stamped on each rod faces towards the same side as the number stamped on the big end.

	Value - daNm	Fastening	Component	Ø
.	2.0 + 60°	Bolt	CONNECTING ROD CAP	M9

- Use the tool for the angular tightening of the connecting rod bolts.

	Description	Code	Function
.	Torque wrench	1.860.942.000	Angular tightening of bearing cap bolts

- Remove the tool for rotating the crankshaft.

	Description	Code	Function
.	Flange	1.860.815.000	Crankshaft rotation

- Position the engine oil intake duct complete with gasket in its housing and secure it using the bolts.- Clean the matching surfaces between the crankcase sump and the cylinder block/crankcase.- Apply silicon sealant to the entire perimeter of the crankcase sump.1. Place the crankcase sump back in its housing.2. Tighten the side bolts (2a) fixing the crankcase sump to the recommended torque using the spanner (2b).

	Value - daNm	Fastening	Component	Ø
2a	(Engine crankcase side) 0.9 -1.2	Side bolts	OIL SUMP	M6

	Description	Code	Function
2b	Spanner	1.860.833.000	Loosen/tighten crankcase sump side bolts

3. Tighten the front and rear bolts (3a) fixing the crankcase sump to the recommended torque using the spanner (3b).

	Value - daNm	Fastening	Component	Ø
3a	(Engine crankcase side) 2.3 - 3.3	Front and rear bolts	OIL SUMP	M8

	Description	Code	Function
3b	Spanner	1.860.834.000	Loosen/tighten front and rear crankcase sump bolts