1008A44 RIGID REAR POWER UNIT MOUNTING - R.R. - Lancia - THESIS - eLearn

74604 - 1008A44 RIGID REAR power unit MOUNTING - R.R.

) - Position the vehicle on a lift.- Open the boot and disconnect the negative battery terminal. See in Op. 7040D50 ENGINE COMPARTMENT UPPER SOUND INSULATION SHIELD - R.R. See in Op. 7055B54 PROTECTION/GUARD under engine - R.R. See in Op. 4450B04 Right FRONT WHEEL (one) - R.R. See in Op. 7055B42 FRONT WHEEL ARCH LINER (one), left or right - R.R. See in Op. 7055B64 Engine compartment DUST SEAL in front wheel arch (one), left or right - R.R. See in Op. 2710A30 INTERMEDIATE DRIVE SHAFT - R.R. with right driveshaft removed See in Op. 1016A40 Ignition COIL COVER on cylinder head - R.R. See in Op. 1092G10 Engine components single drive BELT - R.R.1. Undo the bolts fixing the alternator.- Disconnect the alternator electrical cables.

	Description	Connector
.	Alternator	A010A

	Description	Connector
.	Alternator	A010B

2. Remove the alternator.

1. Undo the retaining bolts.2. Remove the alternator rear mounting bracket.

- Position the hydraulic engine support under the oil sump in order to work safely.1. Remove the air intake chamber mounting bracket (1a) acting on the bolt (1b) and the nut (1c).

1. Disconnect the electrical connection for the engine oil pressure sensor.

	Description	Connector
1	Insufficient engine oil pressure sensor	K030

2. Undo the nut fixing the support to the flexible mounting.3. Undo the bolt fixing the support to the oil sump.- Keep the spacers which are between the bolt and the sump.4. Undo the bolts fixing the support to the cylinder block/crankcase.5. Remove the intermediate driveshaft support which supports the engine.

Refitting ( Removing

) - Still working with the hydraulic engine support positioned under the engine oil sump, fit the intermediate driveshaft support.- Tighten the bolts fixing the support to the cylinder block/crankcase to the recommended torque.

	Value - daNm	Fastening	Component	Ø
.	(to the cylinder block/crankcase) 5	Bolt	RIGID REAR SUPPORT POWER UNIT	M12 X 1.25

- Position the spacers and tighten the bolt fixing the support to the oil sump to the recommended torque.

	Value - daNm	Fastening	Component	Ø
.	(on the crankcase sump) 2.5	Nut	RIGID REAR SUPPORT POWER UNIT	M8

- Tighten the nut fixing the support to the flexible mounting to the recommended torque.

	Value - daNm	Fastening	Component	Ø
.	(to the flexible mounting) 5	Nut	RIGID REAR SUPPORT POWER UNIT	M10 X 1.25

- Connect the electrical connection for the engine oil pressure sensor.

	Description	Connector
.	Insufficient engine oil pressure sensor	K030

- Position the intake chamber mounting bracket.- Fit the alternator rear mounting bracket.- Remove the hydraulic support- Position the alternator and fasten it using the fixing bolts.

	Value - daNm	Fastening	Component	Ø
.	5	Nut	ALTERNATOR ASSEMBLY	M10 X 1.25

	Value - daNm	Fastening	Component	Ø
.	7	Nut	ALTERNATOR ASSEMBLY	M12 X 1.25

- Connect the alternator electrical cables.

	Description	Connector
.	Alternator	A010A

	Description	Connector
.	Alternator	A010B

See in Op. 1092G10 Engine components single drive BELT - R.R. See in Op. 1016A40 Ignition COIL COVER on cylinder head - R.R. See in Op. 2710A30 INTERMEDIATE DRIVE SHAFT - R.R. with right driveshaft removed See in Op. 7055B64 Engine compartment DUST SEAL in front wheel arch (one), left or right - R.R. See in Op. 7055B42 FRONT WHEEL ARCH LINER (one), left or right - R.R. See in Op. 4450B04 Right FRONT WHEEL (one) - R.R. See in Op. 7055B54 PROTECTION/GUARD under engine - R.R. See in Op. 7040D50 ENGINE COMPARTMENT UPPER SOUND INSULATION SHIELD - R.R.- Connect the battery terminal.- Remove the vehicle from the lift.