939003715 - N020 HORNS NOT WORKING

0	PRELIMINARY CHECKS	ALL OK	PROBLEMS ENCOUNTERED	ACTION
	Check, by operating the horn control on the steering wheel, that the travel is correct	Move on to Step 1	Travel not correct	Remove the steering wheel and check that there are no impediments to the travel.Op. 4110A11 STEERING WHEEL - R+R FOR REPLACEMENT OR CHECK FOR VERSIONS WITH AIR BAGIf there are problems, replace the faulty component
1	CHECK ON INTERVENTION OF FUSE	ALL OK	PROBLEMS ENCOUNTERED	ACTION
	Check that the horn protective fuse has not blown.It can be found in the engine compartment junction unit and is the third fuse in the first row F10 (15 A).	Move on to Step 2	The fuse has blown	Replace the fuse and search for the cause of the problem.
2	RELAY CHECK	ALL OK	PROBLEMS ENCOUNTERED	ACTION
	Swap the horn relay feed T3 (it is the middle one in the top row) with the one for the main beam headlamps T2 (it is the first on the left in the top row) and check that the horn is working properly.	Move on to Step 3	The horn continues not to work	Restore the relays to their places and move on to Step 4
3	RELAY CHECK	ALL OK	PROBLEMS ENCOUNTERED	ACTION
	Check that the main beam headlamps are working. If the result is positive, remove the horn relay feed and check that the contacts do not show signs of oxidation or deformation.	End of diagnosis	1. The main beam headlamps are not working	1. Replace the main beam headlamp relay (which was originally the one for the horns)
			2. There are problems with the contacts in the engine compartment junction unit.	2. Renew the contacts.If necessary, replace the engine compartment junction unit    Op. 5505A13 ADDITIONAL JUNCTION UNIT IN ENGINE COMPARTMENT - R.R.
4	RELAY ELECTRICAL CHECK	ALL OK	PROBLEMS ENCOUNTERED	ACTION
	Undo the fastenings for the engine compartment junction unit and check, using a tester, that the power supply and the earth for the horn relay feed are correct.    Op. 5505A13 ADDITIONAL JUNCTION UNIT IN ENGINE COMPARTMENT - R.R.	Move on to Step 5	Relay line electrical problems.	Move on to Step 8
5	HORN ELECTRICAL CHECK	ALL OK	PROBLEMS ENCOUNTERED	ACTION
	Using a tester, connect to the horn power supply line and check that whilst the horn is working the supply voltage is more than 11.4 V.Also check the continuity and the insulation of the line	Move on to Step 6	1. The voltage is below 11.4 V	1. Check the cause of the power supply and restore the correct power supply.Possibly    See Test 5530BC BATTERY CHARGE CHECK
			2. Other electrical problems	2. Restore the correct electrical connections    See E3010 HORNS
6	HORN POSITIONING CHECK	ALL OK	PROBLEMS ENCOUNTERED	ACTION
	Check that both the horn casing and the bracket are not touching or are not in the immediate vicinity (less than 10 mm) of other objects (other components, cables, pipes, etc.)	Move on to Step 7	Horn bracket or casing interfering with other components.	Eliminate the cause of the interference
7	STEERING COLUMN SWITCH UNIT CHECK	ALL OK	PROBLEMS ENCOUNTERED	ACTION
	Remove the steering wheel and check that there is nothing preventing the operation of the horn control switch.Using a tester in parallel to the switch check that, whilst it is working, the supply voltage is more than 11.4 V	Move on to Step 9	1. Switch stuck open	1. Replace the steering wheelOp. 4110A11
			2. Switch power supply problems.	2. Replace the steering column switch unit.Op. 5550A12
8	HORN CHECK	ALL OK	PROBLEMS ENCOUNTERED	ACTION
	Remove the horn and connect it directly to a battery charger.    Op. 5550B30 L/H OR R/H HORN (ONE) - R+R Check that a sound is produced and there are no unpleasant noises (knocking/buzzing)	Move on to Step 9	Sound faulty or no sound produced.	Replace the horn    Op. 5550B30 L/H OR R/H HORN (ONE) - R+R
9	ELECTRICAL CIRCUIT CHECK	ALL OK	PROBLEMS ENCOUNTERED	ACTION
	The problem is due to the presence of an irregular electrical absorption source in the electrical system.Search for and eliminate this cause	End of diagnosis