| STEP | CHECK TO BE PERFORMED | RESOLUTION IF THE CHECK IS NOT OK |
|---|
| 1 | With the ignition ON, check for the presence at Pin 5 of the headlamp alignment corrector front potentiometer connector See K001 HEADLAMP ALIGNMENT CORRECTOR FRONT POTENTIOMETER (CAF)of a voltage of 5 V.Move on to Step 5 | Move on to Step 2 |
| 2 | If faults are present, restore the continuity of the wiring between the Master headlamp (left side) and the front potentiometer See E3080 HEADLAMP AGLINMENT CORRECTOR The test can be considered over | Move on to Step 3 |
| 3 | With the key ON, check for the presence at Pin 1 of the Master headlamp See F010 LEFT HEADLAMP of a voltage of 5 V. | Replace the master headlamp Op. 5540B81 LEFT GAS DISCHARGE LIGHT CLUSTER - R.R. |
| 4 | Check the fault disappears.The test can be considered over | Replace the headlamp control unitOp. 5540B42 |
| 5 | With the ignition ON, check for the presence at Pin 5 of the headlamp alignment corrector rear potentiometer connector See K002 HEADLAMP ALIGNMENT CORRECTOR REAR POTENTIOMETER (CAF)of a voltage of 5 V.Move on to Step 8 | Move on to Step 6 |
| 6 | If faults are present, restore the continuity of the wiring between the Master headlamp (left side) and the rear potentiometer See E3080 HEADLAMP AGLINMENT CORRECTOR The test can be considered over | Move on to Step 7 |
| 7 | With the key ON, check for the presence at Pin 4 of the headlamp See F010 LEFT HEADLAMP of a voltage of 5 V.Move on to Step 4 | Replace the master headlamp Op. 5540B81 LEFT GAS DISCHARGE LIGHT CLUSTER - R.R. |
| 8 | Check Pin 1 of the potentiometer connector See K001 HEADLAMP ALIGNMENT CORRECTOR FRONT POTENTIOMETER (CAF)for the presence of a negative signal.Move on to Step 11 | Move on to Step 9 |
| 9 | If faults are present, restore the continuity of the wiring between the Master headlamp (left side) and the front potentiometer See E3080 HEADLAMP AGLINMENT CORRECTOR The test can be considered over | Move on to Step 10 |
| 10 | With the key ON, check for the presence at Pin 4 of the headlamp See F010 LEFT HEADLAMP of an earth signal.Move on to Step 4 | Replace the master headlamp Op. 5540B81 LEFT GAS DISCHARGE LIGHT CLUSTER - R.R. |
| 11 | Check Pin 1 of the potentiometer connector See K002 HEADLAMP ALIGNMENT CORRECTOR REAR POTENTIOMETER (CAF)for the presence of a negative signal.Move on to Step 14 | Move on to Step 12 |
| 12 | If faults are present, restore the continuity of the wiring between the Master headlamp (left side) and the rear potentiometer See E3080 HEADLAMP AGLINMENT CORRECTOR The test can be considered over | Move on to Step 13 |
| 13 | With the key ON, check for the presence at Pin 6 of the headlamp See F010 LEFT HEADLAMP of an earth signal.Move on to Step 4 | Replace the master headlamp Op. 5540B81 LEFT GAS DISCHARGE LIGHT CLUSTER - R.R. |
| 14 | Turn the ignition key ON.Disconnect the front sensor connecting rod.Connect a Voltmeter across Pin 2 of the headlamp 6-way connector See F010 LEFT HEADLAMP and Earth.Check that the voltage varies from 0.5 and 4.5 V when the sensor mobile axis is turned by hand.Move on to Step 16 | Move on to Step 15 |
| 15 | If faults are present, restore the continuity of the wiring between the Master headlamp (left side) and the front potentiometer See E3080 HEADLAMP AGLINMENT CORRECTOR The test can be considered over | Replace the sensor Op. 5540C42 SENSOR FOR CORRECTING/ALIGNING GAS DISCHARGE LIGHTING UNITS ON FRONT SUSPENSION - R R |
| 16 | Turn the ignition key ON.Disconnect the rear sensor connecting rod.Connect a Voltmeter across Pin 5 of the headlamp 6-way connector See F010 LEFT HEADLAMP and Earth.Check that the voltage varies from 0.5 and 4.5 V when the sensor mobile axis is turned by hand.The test can be considered over | Move on to Step 17 |
| 17 | If faults are present, restore the continuity of the wiring between the Master headlamp (left side) and the rear potentiometer See E3080 HEADLAMP AGLINMENT CORRECTOR | Replace the sensor Op. 5540C46 SENSOR FOR CORRECTING/ALIGNING GAS DISCHARGE LIGHTING UNITS ON REAR SUSPENSION - R.R. |