939011755 - E5030 PETROL ENGINE ELECTRONIC MANAGEMENT - OPERATIONAL DESCRIPTION
FUNCTIONAL DESCRIPTION
The engine management control unit M10 controls and governs the entire electronic ignition and injection system.The control unit M10 receives a direct supply from the battery at pin 92 of connector A via the line protected by fuse F18 of junction unit B1.The ignition-operated power supply (15/54) arrives from the line protected by fuse F16 of the engine compartment junction unit B1 at pin 67 of connector A of M10.The main injection relay T9 of B1 controls the entire system: it is energized by an (earth) control signal coming from pin 25 of connector A of control unit M10 and, consequently, sends a power supply:- to pins 3, 5 and 6 of connector A of the actual control unit, via the line protected by fuse F22 of B1;- to the air flow meter K41, to the fuel vapour recovery solenoid valve L10, to the phase transformers N92 and N93 and to the Lambda sensors K15, K16, K17 and K18 and lastly to the high pressure pump N77; (all these lines are protected by fuse F11 of B1);- to the coils A30, via the line protected by fuse F17 of B1.The fuel pump relay T10 of B1 is supplied by the line for fuse F21 of B1.It is energized by a control signal coming from pin 8 of connector A of control unit M10 and provides the power supply for the electric fuel pump N40 which is earthed via the inertia switch I50 which interrupts the circuit in the case of an impact and stops the dangerous supply of fuel.The engine management control unit M10 receives signals from the various sensors thereby keeping all the engine operating parameters under control.The rpm sensor K46 provides information, via a frequency signal sent to pins 40 and 55 of connector B of the control unit M10, about the engine speed.The intake side timing sensor K106 receives a power supply form pin 24 of connector B of control unit M10 and a reference earth from pin 7 of connector B and sends a frequency signal corresponding to the timing to pin 41 of connector B of the actual control unit.The exhaust side timing sensor K107 receives a power supply form pin 24 of connector B of control unit M10 and a reference earth from pin 7 of connector B and sends a frequency signal corresponding to the timing to pin 56 of connector B of the actual control unit.The fuel pressure sensor K83 receives a power supply form pin 24 of connector B of control unit M10 and a reference earth from pin 27 of connector B and sends a frequency signal corresponding to the fuel pressure to pin 8 of connector B of the actual control unit.The engine temperature sender unit K36 receives a reference earth from pin 7 of connector B of the control unit M10 and provides a signal proportional to the temperature of the engine coolant at pin 22 of connector B of the control unit.The four Lambda sensors K15, K16, K17 and K18 provide the control unit M10 with information surrounding the correct composition of the air/fuel mixture in different exhaust positions: two - linear type - are located upstream of the preconverters while two flat sensors are located downstream of the preconverters.The linear sensor K15 sends the signals to pins 55, 56, 77 and 78 of connector A of M10, whilst it is heated by a resistance to ensure correct operation even when cold. The resistance is supplied by fuse F11 of B1 and receives an earth signal from pin 73 of connector A of control unit M10.The linear sensor K16 sends the signals to pins 57, 58, 79 and 80 of connector A of M10, whilst it is heated by a resistance to ensure correct operation even when cold. The resistance is supplied by fuse F11 of B1 and receives an earth signal from pin 51 of connector A of control unit M10.The planar sensor K17, sends the signals to pins 74 and 75 of connector A of M10 whilst it is heated by a resistance supplied by fuse F11 of B1 and receives an earth signal from pin 50 of connector A of control unit M10.The planar sensor K18 sends the signal to pins 52 and 53 of connector A of M10 whilst it is heated by a resistance supplied by fuse F11 of B1 and receives an earth signal from pin 94 of connector A of control unit M10.The detonation sensor K50 makes it possible to have information about detonation conditions by means of a frequency signal sent to pin 44 of connector B of control unit M10: it receives a reference earth from pin 59 of connector B.The detonation sensor K51 makes it possible to have information about detonation conditions by means of a frequency signal sent to pin 58 of connector B of control unit M10: it receives a reference earth from pin 43 of connector B.The air flow meter K41 (supplied by fuse F11 of B1) is connected to pins 11, 12, 26 and 27 of connector B of control unit M10.The accelerator pedal K55 has two built in potentiometers (one main one and one safety one). The first receives the power supply and earth respectively from pins 83 and 81 of connector A of M10 and sends the corresponding signal to pin 82 of 59 and 61 of connector A of M10 and sends the signal to pin 60 of the same connector.Control unit M10 receives the mininum engine oil pressure sensor K30 signal at pin 28 of connector B.Pin 14 of connector A of M10 receives the signal coming from the brake lights switch I30 - N.A. contact - with an ignition-controlled supply (INT) from fuse F37 of junction unit B2; it receives the signal - N.C. contact - coming from the brake lights switch I30 at pin 20 of connector A of M10 with an ignition-controlled supply (INT) from fuse F35 of junction unit B2.Pin 32 of connector A of M10 receives the signal coming from the clutch switch I31.The control unit M10 controls the opening of the individual injectors N70, through the special signals sent from pins 49 and 50 (cyl. 1), 47 and 48 (cyl. 2), 32 and 33 (cyl. 3) and 34 and 35 (cyl. 4) of connector B of M10. The fuel pressure regulator N77 is operated by the control unit M10 from pin 2 of connector B.The control unit M10 also controls the coil A30 (supplied by fuse F17 of B1) via the (earth) control signals for the coil primary windings, whilst the secondary winding sends the impulse to the spark plugs: from pins 16, 1, 31 and 46 of connector B of M10 for cylinders 1, 2, 3 and 4 respectively.The throttle body actuator N75 has two built in potentiometers connected in parallel: this controls the throttle opening by means of a stepping motor.The motor receives a power supply from pins 15 and 30 of connector B of M10. Pin 24 of connector B sends the power supply to the two potentiometers, pin 9 provides the earth signal for them, whils pins 10 and 25 of the same connector receive signals that arrive from the throttle body actuator N75.The fuel vapour recovery solenoid valve L10 allows the flow of fuel vapours to the engine intake where they are added to the mixture entering the combustion chamber. The valve L10 is opened by the control unit when the engine is in load conditions by means of a duty cycle type signal from pin 18 of connector B of M10.The inlet side phase transformer N92 mechanically controls the timing advance at the intake: it is controlled by pin 4 of connector B of the control unit.The exhaust side phase transformer N93 mechanically controls the timing advance at the intake: it is controlled by pin 19 of connector B of the control unit.The control unit M10 is then connected via the CAN to the Body Computer M1 and to the other network nodes: information on the following is sent through this connection- system autodiagnosis, that can be used by connecting to connector C of M1: signals arrive from pin 87 of connector A from the control unit M10 via the special diagnostic line;- engine coolant temperature, which is sent to the instrument panel E50 which manages the gauge and the warning light;- engine rpm, which is sent to the instrument panel E50 rev counter;- minimum engine oil pressure, which is sent to the instrument panel E50 which manages the warning light;It receives the speedometer signal, via the CAN, produced by the ABS control unit M50.The autodiagnostic system for the control unit M10 also produces a signal - which leaves pin 68 of connector A - which is connected directly to the EOBD warning light in the instrument panel E50.