939003563 - B010 ENGINE DOES NOT START (UNDER ANY CIRCUMSTANCES)

0	PRELIMINARY CHECKS	All OK	Problems encountered	Operation
	Attempt start-up for 15 seconds.Press the START/STOP button to turn on the panel.Check whether any of the following errors are present using the diagnostic equipment: P0115, P0230, P0301, P0302, P0303, P0304, P0335, P0336, P0603, P0604, P0605, P0606, P0638	Move on to Step 1	One or more of the errors indicated is present	Continue as described by the diagnostic equipment
1	CHECK VEHICLE PROTECTION SYSTEM ERRORS	All OK	Problems encountered	Operation
	Check the body computer for errors in the vehicle protection system.	Move on to Step 2	One or more errors in the vehicle protection system is indicated	Continue as described by the diagnostic equipment
2	FUEL PUMP RELAY CHECK	All OK	Problems encountered	Operation
	Insert the ignition key and check the pump comes on for 2 seconds	Move on to Step 3	The pump is not activated	Check that the fuel pump relay is working properly    See Test 1040AD FUEL PUMP RELAY CHECK
3	POWER SUPPLY CIRCUIT CHECK	All OK	Problems encountered	Operation
	Check there are no faults in the fuel supply circuit by carrying out test    See Test 1040OA FUEL SUPPLY CIRCUIT CHECK	Move on to Step 4	Faults present	The test indicates the solution
4	RPM SENSOR ERROR CHECK	All OK	Problems encountered	Operation
	Connect the diagnostic equipment and check that error P0335 is not present	Move on to Step 5	Error P0335 is present	Continue as described by the diagnostic equipment
5	AIR INTAKE CIRCUIT CHECK	All OK	Problems encountered	Operation
	Check there are no faults in the air intake circuitIn particular, check:- that the air filter is not blocked or fitted incorrectly- that the air intake circuit does not contain abnormal restrictions or leaks or is not incorrectly fitted	Move on to Step 6	Air filter blocked	Replace the filter element    Op. 1048A14 AIR CLEANER FILTER ELEMENT - REPLACE.
			Faulty component	Replace the faulty component    Op. 1048 ENGINE AIR SUPPLY CIRCUIT
			Components incorrectly positioned	Refit the faulty component correctly    Op. 1048 ENGINE AIR SUPPLY CIRCUIT
6	CHECK FOR IMPURITIES IN THE FUEL	All OK	Problems encountered	Operation
	Check that the fuel does not contain impurities such as water, alcohol or suspended particles by performing test    See Test	Move on to Step 7	Faults present	The test indicates the solution
7	SPARK PLUG CHECK	All OK	Problems encountered	Operation
	Remove the spark plugs.    Op. 5510D10 SPARK PLUGS - R+Rand check that they do not display signs of faults as indicated in the test    See Test	Move on to Step 8	Faults present	The test indicates the solution
8	FLOW METER CHECK	All OK	Problems encountered	Operation
	Disconnect the flow meter so that the engine control unit enters recovery mode and calculates air flow using default values.Check that the fault persists under these conditions	Move on to Step 9	The engine starts normally when the flow meter is disconnected	The flow meter is faulty: delete the errors and replace the flow meter    Op. 1056F09 HOT FILM AIRFLOW METER DEBIMETER R R
9	CYLINDER COMPRESSION CHECK	All OK	Problems encountered	Operation
	Carry out the cylinder compression check    Op. 0510A10 CYLINDER COMPRESSION - CHECK FOR LOOSE SPARK PLUGS OR INJECTORS	Move on to Step 11	Cylinder compression insufficient	Move on to Step 10
10	CHECK ON CAUSE OF INSUFFICIENT COMPRESSION	All OK	Problems encountered	Operation
	R/R head for valve leakage test    Op. 1016C10 SINGLE CYLINDER HEAD - R.R. AND REPLACE GASKET Check condition of cylinders/piston rings	Move on to Step 11	Valve seal insufficient	Overhaul the head    Op. 1016E10 SINGLE CYLINDER HEAD, REMOVED - OVERHAUL
			Cylinders/piston rings worn	Restore the seal
			Cylinder head/cylinder block-crankcase matching faulty	Restore correct matching
11	TIMING CHECK	All OK	Problems encountered	Operation
	Check that the valve gear timing is correct    Op. 0510A20 TIMING GEAR WITH BELT DRIVE - CHECK - CARRY OUT OPERATION WITH CAM COVER(S) REMOVED AND TAPPETS ADJUSTED AND CRANKSHAFT PULLEY DETACHED (IF NECESSARY)	Move on to Step 12	Valve gear timing not correct	Restore the correct valve gear timing
12	EXHAUST PIPE CHECK	All OK	Problems encountered	Operation
	Check the exhaust circuit for leaks, loose connections, restrictions, deformations or damage	Move on to Step 13	Faults present	Restore correct fastening of faulty parts. Replace them if necessary.
13	CHECK WATER TEMPERATURE SENSOR ERRORS	All OK	Problems encountered	Operation
	Connect the diagnostic equipment and check that error P0115 is not present	Move on to Step 14	Error P0115 present	Continue as described by the diagnostic equipment
14	ERROR DELETION	All OK	Problems encountered	Operation
	Use the diagnostic instrument to delete the errors and check start-up is successful	Move on to Step 15	The engine still will not start	Move on to Step 0
15	CHECK ON CORRECT OPERATION	All OK	Problems encountered	Operation
	Allow the engine to warm up while idling.Check that the diagnostic instrument has not detected any more errors in the control unit	End of diagnosis	Errors still present in control unit	Continue as described by the diagnostic equipment