939010574 - 1060G90 SYSTEM CABLE LOOM - R.R.

Removing ( Refitting ) - Position the vehicle on a lift.    Op. 1016A10 SOUND-PROOFING COVER - R.R     Op. 5530B10 BATTERY - R+R     Op. 5530B52 BATTERY SUPPORT/DRIP TRAY - R.R     Op. 1048A10 AIR FILTER ASSEMBLY - R.R.     Op. 4450B04 RIGHT FRONT WHEEL - R.R     Op. 7055B66 ENGINE COMPARTMENT DUST COVER IN RIGHT FRONT WHEEL ARCH - R.R.     Op. 7055B91 RIGHT FRONT WHEEL ARCH LINER - R.R.     Op. 7055B54 UNDER ENGINE PROTECTION/GUARD - R.R. 1. Disconnect the electrical connections from the diesel electronic injection system control unit.

	Description	Connector
1	Engine management control unit	See M010 ENGINE MANAGEMENT ECU

1. Disconnect the electrical connection of the air conditioner compressor.

	Description	Connector
1	Air conditioning compressor engagement electro-magnet	See L020 AIR CONDITIONING COMPRESSOR ENGAGEMENT ELECTRO-MAGNET

1. Disconnect the electrical connection from the air conditioning system multi-stage pressure switch.

	Description	Connector
1	4 stage pressure switch	See K010 4 STAGE PRESSURE SWITCH

2. Undo the nut (2a) and disconnect the earth lead (2b). 1. Release the electrical wiring from the securing bands and move it aside. 1. Disconnect the intermediate engine wiring coupling...

	Description	Connector
1	Engine cables/engine services cable coupling	See D029 ENGINE CABLES/ENGINE SERVICES CABLE COUPLING

2. Disconnect the electrical connections from the heater plugs control unit.

	Description	Connector
2	Heater plugs control unit	See M015 PLUG PREHEATING CONTROL UNIT

3. Undo the nut (3a) and remove the heater plugs control unit (3b) after having disconnect the remaining electrical connection (3c).

	Description	Connector
3c	Heater plugs control unit	See M015 PLUG PREHEATING CONTROL UNIT

4. Disconnect the intermediate coupling for the cam angle sensor.

	Description	Connector
4	Timing sensor	See K047 TIMING SENSOR

1. Disconnect the electrical connection from the EGR system solenoid valve

	Description	Connector
1	EGR solenoid valve	See L030 EGR SOLENOID VALVE

1. Disconnect the electrical connection from the engine coolant temperature sensor.

	Description	Connector
1	Engine coolant temperature sensor/sender unit	See K036 ENGINE COOLANT TEMPERATURE SENSOR/SENDER UNIT

1. Disconnect the electrical connection from the throttle casing.

	Description	Connector
1	Integrated throttle casing actuator	See N075 THROTTLE BODY ACTUATOR

2. Disconnect the electrical connection from the fuel pressure sensor.

	Description	Connector
2	Fuel pressure sensor	See K083 FUEL PRESSURE SENSOR

1. Disconnect the electrical connection for the exhaust gas temperature sensor on the particle filter.

	Description	Connector
1	Downstream catalytic converter temperature sensor	See K188 CAT. DOWNSTREAM TEMPERATURE SENSOR

1. Disconnect the electrical connections from the injectors.

	Description	Connector
1	Injector	See N070 INJECTOR

2. Undo the bolts (2a) and rmove the electrical wiring (2b) aside. 1. Undo the bolts (1a) and move the fuel return manifold (1b) sideways.2. Disconnect the electrical connection from the fuel pressure regulator on the pressure pump.

	Description	Connector
2	Fuel pressure regulator on pressure pump	See N077 FUEL PRESSURE REGULATOR

3. Disconnect the electrical connection from the fuel pressure regulator on the injector single manifold.

	Description	Connector
2	Fuel pressure regulator on rail	See N087 FUEL PRESSURE REGULATOR ON RAIL

1. Undo the nut (1a) and disconnect the earth lead (1b) from the starter motor.

	Description	Connector
1b	Starter motor	See A020 STARTER MOTOR

1. Disconnect the electrical connection from the engine oil pressure warning light switch.

	Description	Connector
1	Insufficient engine oil pressure sensor (switch)	See K030 LOW ENGINE OIL PRESSURE SENSOR (SWITCH)

1. Disconnect the electrical connection from the engine rpm sensor.

	Description	Connector
1	Engine rpm sensor	See K046 RPM SENSOR

2. Disconnect the electrical connection from the engine oil level sensor.

	Description	Connector
2	Engine oil level sensor	See K032 ENGINE OIL LEVEL SENSOR

1. Undo the nut (1a) and disconnect the earth lead (1b) from the alternator. - Release the system cable loom from the fastenings and remove it. Refitting ( Removing ) - Place the system cable loom in its housing and secure it.- Connect the earth lead to the alternator and secure it using the nut.- Connect the electrical connection to the engine oil level sensor.- Connect the electrical connection for the engine rpm sensor.- Connect the electrical connection to the engine oil pressure warning light switch.- Connect the earth lead to the starter motor and secure it using the nut.- Connect the electrical connection to the fuel pressure regulator on the injector single manifold.- Connect the electrical connection to the fuel pressure regulator on the pressure pump.- Place the fuel return manifold pipe in its housing and secure it using the bolts.- Place the electrical wiring in position and fasten it using the bolts.- Connect the electrical connections to the injectors.- Connect the electrical connection to the exhaust gas temperature sensor to the particle filter.- Connect the electrical connection to the fuel pressure sensor.- Connect the electrical connection to the throttle casing.- Connect the electrical connection to the engine coolant temperature sensor.- Connect the electrical connection for the pressure relief sensor.- Connect the electrical connection to the E.G.R. solenoid valve.- Connect the intermediate coupling for the cam angle sensor.- Connect the electrical connections to the heater plugs control unit then place it in its housing and secure it using the nut.- Connect the electrical connections to the heater plugs control unit.- Connect the intermediate engine wiring coupling.- Place the electrical wiring in position and fasten it to the bands.- Connect the earth lead and tighten the nut.- Connect the electrical connection to the air conditioning system multi-stage pressure switch.- Connect the air conditioning compressor electrical connection.- Connect the electrical connections to the diesel electronic injection system control unit.    Op. 7055B54 UNDER ENGINE PROTECTION/GUARD - R.R.     Op. 7055B91 RIGHT FRONT WHEEL ARCH LINER - R.R.     Op. 7055B66 ENGINE COMPARTMENT DUST COVER IN RIGHT FRONT WHEEL ARCH - R.R.     Op. 4450B04 RIGHT FRONT WHEEL - R.R     Op. 1048A10 AIR FILTER ASSEMBLY - R.R.     Op. 5530B52 BATTERY SUPPORT/DRIP TRAY - R.R     Op. 5530B10 BATTERY - R+R     Op. 1016A10 SOUND-PROOFING COVER - R.R - Remove the vehicle from the lift.