939010911 - 5040A20 AIR CONDITIONING COMPRESSOR - R+R - INCLUDES FLUID LEVEL CHECK AND TOP UP IF NECESSARY

Removing ( Refitting )
Follow the safety instructions    Op. 5040 AIR CONDITIONING CASING AND COMPONENTS
- Position the vehicle on a lift.- Drain the coolant    Op. 0010T84 COOLANT FOR AIR CONDITIONING SYSTEM - DEHYDRATE AND REPRESSURIZE     Op. 1048A28 VACUUM AIR CIRCUIT RESONATOR PIPE - R+R     Op. 1060G10 AIR FLOW METER - R.R. 1. Undo the bolt (1a) and disconnect the connector (1b) from the compressor (1c).
Seal the connectors that have been disconnected using suitable plugs to prevent dampness and impurities from entering the system.
- Raise the vehicle.    Op. 4450B04 RIGHT FRONT WHEEL - R.R     Op. 7055B54 UNDER ENGINE PROTECTION/GUARD - R.R.     Op. 1092G10 SINGLE ENGINE BELT - R.R     Op. 1048B14 AIR DELIVERY HOSE BETWEEN TURBOCHARGER AND HEAT EXCHANGER - REPLACE 1. Disconnect the electrical connection.
DescriptionComponent
AIR CONDITIONING COMPRESSOR ENGAGEMENT ELECTROMAGNET    See L020 AIR CONDITIONING COMPRESSOR ENGAGEMENT ELECTRO-MAGNET
2. Undo the compressor fixing bolts.3. Keep the compressor.
- If the compressor is being replaced, proceed as follows.1. Drain the fluid from the compressor through the drainage opening (1a) after having removed the screw plug (1b) and throught the attachment openings for the pipe connectors (1c). If necessary, rotate the compressor several times manually, using the pulley to ensure that all of the fluid comes out.
The fluid is extremely hygroscopic: avoid leaving the containers open. Avoid leaving the compressor or any of the components disconnected from the system for any longer than is strictly necessary.
1. Collect the fluid drained from the compressor in a suitable transparent container (quantity A).2. Drain the fluid from the new compressor (quantity B) and collect it following the instructions given previously.3. Reintroduce a quantity of oil into the new compressor that corresponds to what was removed from the compressor being replaced (C=B-A).4. The fluid should be introduced into the compressor through the pressurizing/drainage opening- Tighten the screw cap to the recommended torque.
ComponentFasteningdia  Value (daNm)Validity
COMPRESSOR SCREW PLUG1.0 ÷ 1.2
Refitting ( Removing ) - Check that the compressor is not damaged.1. Reposition the compressor.2. Screw in the compressor fixing bolts and tighten them to the specified torque.
ComponentFasteningdia  Value (daNm)Validity
COMPRESSORBoltM8x902.2 ÷ 2.6
3. Connect the electrical connection to the compressor.
    Op. 1048B14 AIR DELIVERY HOSE BETWEEN TURBOCHARGER AND HEAT EXCHANGER - REPLACE     Op. 1092G10 SINGLE ENGINE BELT - R.R     Op. 7055B54 UNDER ENGINE PROTECTION/GUARD - R.R.     Op. 4450B04 RIGHT FRONT WHEEL - R.R - Lower the vehicle.
Replace the O rings for the connectors. Only use green coloured seals that are resistant to R134a coolant. Lubricate the connector threads using anti-freeze.
1. Connect the connector (1b) for the pipe to the compressor (1a) and secure it tightening the bolt (1c) to the recommended torque.
ComponentFasteningdia  Value (daNm)Validity
COMPRESSOR PIPE CONNECTORSBoltM8x301.8 ÷ 2.2
    Op. 1060G10 AIR FLOW METER - R.R.     Op. 1048A28 VACUUM AIR CIRCUIT RESONATOR PIPE - R+R - Repressurize the coolant    Op. 0010T84 COOLANT FOR AIR CONDITIONING SYSTEM - DEHYDRATE AND REPRESSURIZE - Remove the vehicle from the lift.