7005A08 INTERIOR SUPPORT FRAME FOR ONE SIDE DOOR - R.R. WITH DOOR PANEL REMOVED - Alfa - 159 - eLearn

939011109 - 7005A08 INTERIOR SUPPORT FRAME FOR ONE SIDE DOOR - R.R. WITH DOOR PANEL REMOVED

) Op. 7005D30 FRONT SIDE DESCENDING WINDOW GLASS SCRAPER (INNER) (ONE), LEFT OR RIGHT - R.R. Op. 7005D15 FRONT SIDE DOOR DESCENDING WINDOW GLASS (ONE) LEFT OR RIGHT - R.R Op. 7005C17 FRONT SIDE DOOR LOCK BARREL - R.R.1. Disconnect the electrical connection.

Description	Component
DRIVER''S DOOR JUNCTION UNIT	See M066 DRIVER'S DOOR CONTROL UNIT (NPG)
PASSENGER SIDE DOOR JUNCTION UNIT	See M067 PASSENGER DOOR CONTROL UNIT (NPP)

2. Disconnect retainers (2a) of rear view mirror wiring (2b) from the chassis.3. Lift ring nut (3a) and disconnect the door electrical connection (3b).

Description	Component
REAR JOINT/FRONT DOOR DRIVER SIDE	See D030 DRIVER'S FRONT DOOR COUPLING
REAR JOINT/FRONT DOOR PASSENGER SIDE	See D031 PASSENGER FRONT DOOR COUPLING

4. Release the cable duct (4a) from the doro frame opening (4b).5. Cut the door wiring retaining band.6. Push the electrical connection into the door frame as far as possible.7. Undo the bolts fixing the support frame.8. Loosen the lock fixing bolts.9. Move support frame (9a) slightly from the front side and remove connection (9b) from the door frame.

1. Disconnect link (1a) form the door frame (1b), undoing retainers (1c) and (1d).2. Recover the support frame.

- If necessary carry out Op. 7205E37 STRIPPING FRONT SIDE DOOR INTERIOR SUPPORT FRAME

Refitting ( Removing

) - Check that the support frame is not damaged.- If necessary carry out Op. 7205E37 STRIPPING FRONT SIDE DOOR INTERIOR SUPPORT FRAME 1. Before positioning support frame (1a), check that the perimeter seal (1b) is undamaged and clean.Also check that the contact surface on the door frame is clean.

1. Position the support frame.2. Connect link (2a) to door frame (2b), doing up retainers (2c) and (2d).

1. Fit connection (1a) into the door frame so that it emerges from opening (1b).2. Apply collar (2a) to the wiring to reduce free length.Check that wiring (2b) does not interfere with glass movement.3. Position the link from outer handle to lock (3a) as shown in the figure.Before fitting the lock, check that link (3a) is in the position shown in the figure.4. Tighten the lock fixing bolts.

Component	Fastening	dia	Value (daNm)	Validity
DOOR LOCK	Bolt	M6x12	0.7 ÷ 1.1

5. Place frame (5a) in position and secure it using the bolts (5b).

Component	Fastening	dia	Value (daNm)	Validity
DOOR INNER FRAME	Bolt	M6x16	0.7 ÷ 1.1

6. Fit the wiring duct to the door frame.7. Connect electrical connection (7a) to the door and secure with ring nut (7b).8. Disconnect retainers (8a) of rear view mirror wiring (8b) from the chassis.9. Connect the rear view mirror electrical connection.

Op. 7005C17 FRONT SIDE DOOR LOCK BARREL - R.R. Op. 7005D15 FRONT SIDE DOOR DESCENDING WINDOW GLASS (ONE) LEFT OR RIGHT - R.R Op. 7005D30 FRONT SIDE DESCENDING WINDOW GLASS SCRAPER (INNER) (ONE), LEFT OR RIGHT - R.R.