| TEST RESULTS |
| 1 | CHECK USING DIAGNOSTIC EQUIPMENT | ALL OK | PROBLEMS ENCOUNTERED | ACTION |
|---|
| Connect the diagnostic equipment and check at the Engine Management Node for the absence of:- System/component faults- Faults in the CAN network/s | Move on to Step 2 | 1.Fault in CAN2.Presence of errors | 1.Continue as instructed by the diagnostic equipment2.Continue as instructed by the diagnostic equipment |
| 2 | CHECK ON SENSOR FOR PRESENCE OF WATER IN DIESEL FILTER | ALL OK | PROBLEMS ENCOUNTERED | ACTION |
|---|
| Check for presence of water in diesel filterCheck that the sensor supply is correctCheck the operation of the sensor | Move on to Step 2 | 1. Water in the filter2. Supply not correct3. Sensor defective | 1. Replace the filter and refill with diesel that conforms to the specifications2. Restore correct power supply3. Replace the filter mounting and sensor |
| 3 | CHECKS USING DIAGNOSTIC EQUIPMENT | ALL OK | PROBLEMS ENCOUNTERED | ACTION |
|---|
| Connect an Examiner and check on CAN Network Information for the absence of:- Inactive node/s- Node/s with error/s- Node/s with CAN error/s | Move on to Step 6 | 1.Impossible to communicate with the Body Computer2.Instrument Panel Node inactive and/or with error3.Engine Control Node inactive and/or with error4.Fault in CAN | 1. Move on to Step 52. Move on to Step 73.Move on to Step 114.Continue as instructed by the diagnostic equipment |
| 4 | CHECK USING DIAGNOSTIC EQUIPMENT | ALL OK | PROBLEMS ENCOUNTERED | ACTION |
|---|
| Use an Examiner to assess the possibility of connection to the Body Computer Node, to check that there are no errors and to check the presence of parameters. | Move on to Step 3 | 1. Impossible to connect to the Body Computer control unit2. Presence of errors | 1. Move on to Step 42. Continue as described by the diagnostic equipment |
| 5 | ELECTRICAL POWER SUPPLY CHECK | ALL OK | PROBLEMS ENCOUNTERED | ACTION |
|---|
| Check that the power supply to the Body Computer Node and the wiring between the nodes are correct . Check in particular that each individual pin is correctly connected | Move on to Step 4 | 1. Fault in positive electrical supply and/or earth2. Electrical connections not operational | 1. Replace defective component (in the case of a fuse, find out what caused it to blow)2. Restore the damaged wiring to correct operation |
| 6 | CHECK USING DIAGNOSTIC EQUIPMENT | ALL OK | PROBLEMS ENCOUNTERED | ACTION |
|---|
| Use an Examiner to check the possibility of connection to the Body Computer Node | Move on to Step 2 | Impossible to connect to the Body Computer | Replace Body Computer Op. 5505A35 MAIN BODY COMPUTER/JUNCTION UNIT - R.R. |
| 7 | CHECK USING DIAGNOSTIC EQUIPMENT | ALL OK | PROBLEMS ENCOUNTERED | ACTION |
|---|
| Using the Examiner in the Instrument Panel Node mode, check that there are no errors and that the parameters are present | Move on to Step 8 | 1. System fault.2. Fault on CAN network3. Presence of errors | 1. Move on to Step 92. Move on to Step 143. Continue as described by the diagnostic equipment |
| 8 | ELECTRICAL POWER SUPPLY CHECK | ALL OK | PROBLEMS ENCOUNTERED | ACTION |
|---|
| Check the power supply to the node is correct.Check the wiring between the Body Computer and the Instrument Panel. In particular, check that each individual pin is properly connected | Move on to Step 9 | 1. Fault in positive electrical supply and/or earth2. Electrical connections not operational | 1. Replace defective component (in the case of a fuse, find out what caused it to blow)2. Restore the damaged wiring to correct operation |
| 9 | ACTIVE DIAGNOSIS CHECK | ALL OK | PROBLEMS ENCOUNTERED | ACTION |
|---|
| With the Examiner in Instrument Panel Node mode, check that the warning light in question is correctly activated in Active Diagnosis | Move on to Step 10 | The warning light in question does not flash | Replace the Instrument Panel Op. 5560B10 CONTROL PANEL - R+R |
